1 <!doctype linuxdoc system>
5 <!-- Title information -->
7 <title>The DXSpider Installation Manual v1.49</title>
8 <author>Iain Philipps, G0RDI (g0rdi@77hz.com) and
9 Ian Maude, G0VGS, (ianmaude@btinternet.com)</author>
10 <date>December 2001 revision 1.1</date>
13 A reference for SysOps of the DXSpider DXCluster program.
16 <!-- Table of contents -->
19 <!-- Begin the document -->
21 <sect>Linux Installation
26 This section describes the installation of DX Spider v1.47 on a
27 <htmlurl url="http://www.redhat.com" name="RedHat"> Linux Distribution.
28 Wherever possible I will try to include differences for other distributions.
29 I do not intend to try and cover the installation of Linux or the setup
30 of the AX25 utilities. If you need help on this then read Iains original
31 installation guide that comes with the Spider distribution.
34 I am assuming a general knowledge of Linux and its commands. You should
35 know how to use <em>tar</em> and how to edit files using your favourite editor.
38 The crucial ingredient for all of this is
39 <htmlurl url="http://www.perl.org" name="Perl">. Earlier versions of
40 Spider required perl 5.004, however it is now <it>STRONGLY</it> recommended
41 that you use at least version 5.005_03 as this is the version being used
42 in the development of Spider.
45 In addition to the standard Red Hat distribution you will require the
46 following modules from <htmlurl url="http://www.cpan.org/CPAN.html" name="http://www.cpan.org/CPAN.html"> , please note however that with later versions of perl, some of these
47 modules may be included with the distribution. Get the modules anyway and try
48 to install as below. If they complain, they are probably already a part of your
53 <item> <htmlurl url="http://www.cpan.org/modules/by-module/Data/Data-Dumper-2.10.tar.gz" name="Data-Dumper-2.10.tar.gz">
54 <item> <htmlurl url="http://www.cpan.org/modules/by-module/Date/TimeDate-1.10.tar.gz" name="TimeDate-1.10.tar.gz">
55 <item> <htmlurl url="http://www.cpan.org/modules/by-module/IO/IO-1.20.tar.gz" name="IO-1.20.tar.gz (for perl 5.00403 and lower)">
56 <item> <htmlurl url="http://www.cpan.org/modules/by-module/Net/Net-Telnet-3.02.tar.gz" name="Net-Telnet-3.02.tar.gz">
57 <item> <htmlurl url="http://www.cpan.org/modules/by-module/Curses/Curses-1.06.tar.gz" name="Curses-1.06.tar.gz">
58 <item> <htmlurl url="http://www.cpan.org/modules/by-module/Time/Time-HiRes-01.20.tar.gz" name="Time-HiRes-01.20.tar.gz">
62 Copy the CPAN modules listed above to a convenient place on your computer. One good
63 place would be /usr/local/packages, and the instructions which follow will assume that
64 that's where you have put them.
67 Log in as 'root', and make sure you're at '/root' before you continue. Here are exactly the commands you must issue next: -
70 # tar xvfz /usr/local/packages/Data-Dumper-2.10.tar.gz
77 # tar xvfz /usr/local/packages/TimeDate-1.10.tar.gz
84 # tar xvfz /usr/local/packages/IO-1.20.tar.gz
88 # make install UNINST=1
91 # tar xvfz /usr/local/packages/Net-Telnet-3.02.tar.gz
98 # tar xvfz /usr/local/packages/Curses-1.06.tar.gz
105 # tar xvfz /usr/local/packages/Time-HiRes-01.20.tar.gz
106 # cd Time-HiRes-01.20
114 Do not fall into the trap of thinking they're all the same, just because they
115 nearly are! Pay particular attention to the instructions of <em>IO</em>, above.
121 I will assume that you have already downloaded the latest tarball of
122 the DXSpider software and are ready to install it. I am assuming version
123 1.47 for this section but of course you would use the latest version.
126 Login as root and create a user to run the cluster under. <bf><it>UNDER
127 NO CIRCUMSTANCES USE ROOT AS THIS USER!</it></bf>. I am going to use
128 the name <em>sysop</em>. You can call it anything you wish. Depending
129 on your security requirements you may wish to use an existing user,
130 however this is your own choice.
137 For SUSE distributions, the command would be ..
144 Now set a password for the user ...
149 # Retype new UNIX password:
150 passwd: all authentication tokens updated successfully
153 <sect1>Installing the software
156 Now to unpack the DX Spider distribution, set symbolic links and group
157 permissions. Copy the tarball to /home/sysop and do the following.
161 # tar xvfz spider-1.47.tar.gz
162 # ln -s ~sysop/spider /spider
163 # groupadd -g 251 spider (or another number)
167 If you do not have the command <em>groupadd</em> available to you simply
168 add a line in /etc/group by hand.
171 # vi /etc/group (or your favorite editor)
175 You also need to add some others to the group, including your own callsign
176 (this will be used as an alias) and root. The finished line in /etc/group
177 should look something like this
180 spider:x:251:sysop,g0vgs,root
184 The next step is to set the permissions on the Spider directory tree and files ....
187 # chown -R sysop.spider spider
188 # find . -type d -exec chmod 2775 {} \;
189 # find . -type f -exec chmod 775 {} \;
193 This last step allows various users of the group <em>spider</em> to have
194 write access to all the directories. This is not really needed just yet
195 but will be useful when web interfaces start to appear.
198 Finally, you need to fix the permissions on the ax25_call and netrom_call
199 programs. Check where they are with the <em>locate</em> command and alter
200 the permissions with the <em>chmod</em> command like this ..
203 # chown root ax25_call netrom_call
204 # chmod 4775 ax25_call netrom_call
207 <sect1>Setting callsigns etc
210 Now login to your machine as the user you created earlier. In my case that
211 user is called <em>sysop</em>. Once logged in, issue the following commands ....
217 $ cp perl/DXVars.pm.issue local/DXVars.pm
219 $ vi DXVars.pm (or your favourite editor)
223 Using the distributed DXVars.pm as a a template, set your cluster callsign,
224 sysop callsign and other user info to suit your own environment.
231 This is the call sign of your cluster. If you use an SSID then include it here
239 This is the sysop user callsign, normally your own.
242 <bf>PLEASE USE CAPITAL LETTERS FOR CALLSIGNS</bf>
245 Note that this a perl file which will be parsed and executed as part of the
246 cluster. If you get it wrong then perl will complain when you start the cluster
247 process. It is important only to alter the text of any section. Some of the
248 lines look a little odd. Take this line for example ....
251 $myemail = "ianmaude\@btinternet.com";
255 There appears to be an extra slash in there. However this has to be there
256 for the file to work so leave it in.
259 DON'T alter any file in /spider/perl, they are overwritten with every
260 release. Any files or commands you place in /spider/local or /spider/local_cmd
261 will automagically be used in preference to the ones in /spider/perl EVEN
262 while the cluster is running!
265 Save the new file and change directory to ../perl ....
272 Now type the following command which creates the basic user file with you as
279 <sect1>The client program
282 In earlier versions of Spider, all the processes were Perl scripts. This
283 was fine but with a lot of users your computer memory would soon be used up.
284 To combat this a new client was written in "C". This client only works for
285 <em>incoming</em> connects at the moment. Before you can use it though it
286 has to be "made". CD to /spider/src and type <em>make</em>. You
287 should see the output on your screen and hopefully now have a small C program
288 called <em>client</em>. Leave it in this directory.
291 <sect1>Starting up for the first time
294 We can now bring spider up for the first time and see if all is well or not!
295 It should look something like this ...
299 DXSpider DX Cluster Version 1.47
300 Copyright (c) 1998 Dirk Koopman G1TLH
302 loading band data ...
303 loading user file system ...
304 starting listener ...
305 reading existing message headers
307 orft we jolly well go ...
311 If all is well then login on another term or console as <em>sysop</em> and
312 cd to /spider/src. Now issue the following command ...
319 This should log you into the cluster as the sysop under the alias callsign we
320 set earlier. In this case the callsign is G0VGS. The cluster callsign is set
321 in the DXVars.pm file in /spider/local. In this case we will assume that this
322 was set as GB7MBC. You should therefore see this when you login ....
325 G0VGS de GB7MBC 19-Nov-1999 2150Z >
329 If you do, congratulations! If not, look over the instructions again, you
330 have probably missed something out. You can shut spider down again with the
338 and both the cluster and the client should return to Linux prompts.
341 <sect>Linux quick installation guide
344 This section is designed for experienced Spider sysops who want to install
345 Spider from scratch. It is simply a check list of things that need to be
346 done without any explanations. The name in brackets at the end of each line
347 is the user that should be doing that process.
351 <item>Get the additional CPAN modules and install them (root)
352 <item>Create the "sysop" user and set a password (root)
353 <item>Put the Spider tarball in ~sysop and untar it (root)
354 <item>ln -s ~sysop/spider /spider (root)
355 <item>groupadd -g 251 spider (root)
356 <item>Add any more users you need to the group entry in /etc/group (root)
357 <item>Set the permissions on the spider tree (root)
358 <item>Fix permissions on ax25_call and netrom_call (root)
359 <item>Login as the sysop user
360 <item>cd to /spider (sysop)
361 <item>mkdir local (sysop)
362 <item>mkdir local_cmd (sysop)
363 <item>cp perl/DXVars.pm.issue local/DXVars.pm (sysop)
364 <item>cd to /spider/local and edit DXVars to set your details (sysop)
365 <item>cd ../perl (sysop)
366 <item>./create_sysop.pl (sysop)
367 <item>./cluster.pl (sysop)
371 Spider should now be running and you should be able to login using the
376 <item>Enter the correct line in ax25d.conf (root)
377 <item>Enter the correct line in /etc/services (root)
378 <item>Enter the correct line in /etc/inetd.conf (root)
379 <item>killall -HUP inetd (root)
383 Spider should now be able to accept logins via telnet, netrom and ax25.
387 <item>Start the cluster (sysop)
388 <item>set/node and type for links (sysop)
389 <item>Write any connect scripts (sysop)
390 <item>Edit /spider/crontab as required (sysop)
391 <item>Edit any other files as necessary (sysop)
392 <item>Set filters, hops and forwarding files (sysop)
394 <item>Enter the correct line in /etc/inittab (root)
399 <sect1>Allowing ax25 connects from users
402 As stated previously, the aim of this document is not to tell you how to
403 configure Linux or the ax25 utilities. However, you do need to add a line
404 in your ax25d.conf to allow connections to DXSpider for your users. For
405 each interface that you wish to allow connections on, use the following format ...
408 default * * * * * * - sysop /spider/src/client client %u ax25
412 or, if you wish your users to be able to use SSID's on their callsigns ..
415 default * * * * * * - sysop /spider/src/client client %s ax25
419 For most purposes this is not desirable. The only time you probably will
420 need this is when you need to allow other cluster nodes that are using SSID's
421 in. In this case it would probably be better to use the first example and
422 then add a specific line for that node like this:
425 GB7DJK-2 * * * * * * - sysop /spider/src/client client gb7djk-2 ax25
426 default * * * * * * - sysop /spider/src/client client %u ax25
429 <sect1>Allowing telnet connects from users
432 From version 1.47 there is a new (more efficient) way of doing this
433 (see next section) but, if you prefer, the method of doing it described
434 here will continue to work just fine.
437 Allowing telnet connections is quite simple. Firstly you need to add a line
438 in /etc/services to allow connections to a port number, like this ....
441 spdlogin 8000/tcp # spider anonymous login port
445 Then add a line in /etc/inetd.conf like this ....
448 spdlogin stream tcp nowait root /usr/sbin/tcpd /spider/src/client login telnet
452 Once this is done, you need to restart inetd like this ....
459 Now login as <em>sysop</em> and cd spider/src. You can test that spider
460 is accepting telnet logins by issuing the following command ....
463 ./client login telnet
467 You should get a login prompt and on issuing a callsign, you will be given
468 access to the cluster. Note, you will not get a password login. There seems
469 no good reason for a password prompt to be given so it is not asked for.
472 Assuming all is well, then try a telnet from your linux console ....
475 telnet localhost 8000
479 You should now get the login prompt and be able to login as before.
481 <sect1>Setting up telnet connects (from 1.47 onwards)
484 From version 1.47 you can choose to allow the perl cluster.pl program to
485 allow connections directly (i.e. not via the <tt>/spider/src/client</tt>
486 interface program). If you are using Windows then this is the only method
487 available of allowing incoming telnet connections.
490 To do this you need first to remove any line that you may previously have set
491 up in /etc/inetd.conf. Remember to:-
498 to make the change happen...
501 Having done that, you need to copy the file
502 <em>/spider/perl/Listeners.pm</em> to <em>/spider/local</em> and
503 then edit it. You will need to uncomment the line containing &dquot;0.0.0.0&dquot;
504 and select the correct port to listen on. So that it looks like this:-
513 As standard, the listener will listen on all interfaces simultaneously.
514 If you require more control than this, you can specify each interface
519 ["gb7baa.dxcluster.net", 8000],
520 ["44.131.16.2", 6300],
525 This will only be successful if the IP addresses on each interface are static.
526 If you are using some kind of dynamic IP addressing then the 'default' method
527 is the only one that will work.
530 Restart the cluster.pl program to enable the listener.
533 One important difference with the internal listener is that no echoing
534 is done by the cluster program. Users will need to set 'local-echo' on in
535 their telnet clients if it isn't set automatically (as per the standards).
536 Needless to say this will probably only apply to Windows users.
538 <sect1>Setting up for AGW Engine (1.47 onwards)
541 AGW Engine is a Windows based ax25 stack. You can connect to an AGW engine
542 from Linux as well as Windows based machines.
545 In order to enable access to an AGW Engine you need to copy
546 <em>/spider/perl/AGWConnect.pm</em> to <em>/spider/local</em> and edit it.
547 Specifically you must:-
550 <item> set <tt>$enable</tt> to 1.
551 <item> set <tt>$login</tt> and <tt>$passwd</tt> to the values set up in your AGW installation.
552 If you haven't set any there, then you should not touch these values.
553 <item> You can connect to a remote AGW engine (ie on some other machine) by changing <tt>$addr</tt>
554 and <tt>$port</tt> appropriately.
555 <item> Restart the cluster.pl program
559 <sect1>Setting up node connects
562 In order to allow cluster node connections, spider needs to know that the
563 connecting callsign is a cluster node. This is the case whether the connect
564 is incoming or outgoing. In spider this is a simple task and can be done in
568 Later versions of Spider can distinguish different software and treat them
569 differently. For example, the WCY beacon cannot be handles by AK1A type
570 nodes as AK1A does not know what to do with PC73. There are 4 different
571 types of node at present and although they may not have any major
572 differences at the moment, it allows for compatibility. The 4 types are ...
582 For now, we will assume that the cluster we are going to connect to is an
586 Start up the cluster as you did before and login as the sysop with client.
587 The cluster node I am wanting to make a connection to is GB7BAA but you would
588 obviously use whatever callsign you required. At the prompt type ...
595 The case does not matter as long as you have a version of DXSpider later than
596 1.33. Earlier versions required the callsign to be in upper case.
599 That is now set, it is as simple as that. To prove it, login on yet another
600 console as sysop, cd to spider/src and issue the command ...
603 ./client gb7baa (using the callsign you set as a node)
607 You should get an initialisation string from DXSpider like this ...
614 If the callsign you just set up as a cluster node is for an incoming connect,
615 this is all that needs to be done. If the connection is to be outgoing then
616 a connection script needs to be written.
619 Sometimes you make a mistake... Honest, it does happen. If you want to make a node
620 back to being a normal user, regardless
621 of what type it is, do:
627 <sect1>Connection scripts
630 Because DXSpider operates under Linux, connections can be made using just about
631 any protocol; AX25, NETRom, tcp/ip, ROSE etc are all possible examples.
632 Connect scripts live in the /spider/connect directory and are simple ascii files.
633 Writing a script for connections is therefore relatively simple.
636 The connect scripts consist of lines which start with the following keywords
641 <tag/#/All lines starting with a <tt>#</tt> are ignored, as are completely
644 <tag/timeout/<tt>timeout</tt> followed by a number is the number of seconds to wait for a
645 command to complete. If there is no timeout specified in the script
646 then the default is 60 seconds.
648 <tag/abort/ <tt>abort</tt> is a regular expression containing one or more strings to look
649 for to abort a connection. This is a perl regular expression and is
650 executed ignoring case.
652 <tag/connect/<tt>connect</tt> followed by ax25, agw (for Windows users) or telnet and some type dependent
653 information. In the case of a telnet connection, there can be up to
655 The first is the ip address or hostname of the computer you wish to
656 connect to and the second is the port number you want to use (this
657 can be left out if it is a normal telnet session).
658 In the case of an ax25 session then this would normally be a call to
659 ax25_call or netrom_call as in the example above. It is your
660 responsibility to get your node and other ax25 parameters to work
661 before going down this route!
663 <tag/'/<tt>'</tt> is the delimiting character for a word or phrase of an expect/send
664 line in a chat type script. The words/phrases normally come in pairs,
665 either can be empty. Each line reads input from the connection until
666 it sees the string (or perl regular expression) contained in the
667 left hand string. If the left hand string is empty then it doesn't
668 read or wait for anything. The comparison is done ignoring case.
669 When the left hand string has found what it is looking for (if it is)
670 then the right hand string is sent to the connection.
671 This process is repeated for every line of chat script.
673 <tag/client/<tt>client</tt> starts the connection, put the arguments you would want here
674 if you were starting the client program manually. You only need this
675 if the script has a different name to the callsign you are trying to
676 connect to (i.e. you have a script called other which actually
677 connects to GB7DJK-1 [instead of a script called gb7djk-1]).
681 There are many possible ways to configure the script but here are three examples,
682 one for a NETRom/AX25 connect, one for AGW engines and one for tcp/ip.
686 abort (Busy|Sorry|Fail)
687 # don't forget to chmod 4775 netrom_call!
688 connect ax25 /usr/sbin/netrom_call bbs gb7djk g1tlh
692 # you can leave this out if you call the script 'gb7dxm'
700 abort (Busy|Sorry|Fail)
701 # this does exactly the same as the previous example
702 # the '1' is the AGW port number to connect thru for g1tlh
707 # you can leave this out if you call the script 'gb7dxm'
715 connect telnet dirkl.tobit.co.uk
718 # tell GB7DJK-1 that it is connected to GB7DJK
719 # you can leave this out if you call this script 'gb7djk'
724 Both these examples assume that everything is set up properly at the other end.
725 You will find other examples in the /spider/examples directory.
727 <sect1>Starting the connection
730 You start the connection, from within a sysop enabled cluster login, by typing
731 in the word <em>connect</em> followed by a script name like this ....
734 G0VGS de GB7MBC 13-Dec-1998 2041Z >connect gb7djk-1
735 connection to GB7DJK-1 started
736 G0VGS de GB7MBC 13-Dec-1998 2043Z >
740 This will start a connection using the script called <em>gb7djk-1</em>. You can
741 follow the connection by watching the term or console from where you started
742 <em>cluster.pl</em>. From version 1.47 onwards, you will need to <tt>set/debug connect</tt> first.
743 You should see something like this ...
746 <- D G1TLH connect gb7djk-1
747 -> D G1TLH connection to GB7DJK-1 started
748 -> D G1TLH G1TLH de GB7DJK 13-Dec-1998 2046Z >
750 CONNECT sort: telnet command: dirkl.tobit.co.uk
751 CHAT "login" -> "gb7djk"
753 Red Hat Linux release 5.1 (Manhattan)
754 Kernel 2.0.35 on an i586
758 CHAT "word" -> "gb7djk"
760 received "Password: "
762 Connected to GB7DJK-1, starting normal protocol
765 GB7DJK-1 channel func state 0 -> init
767 <- D GB7DJK-1 Last login: Sun Dec 13 17:59:56 from dirk1
768 <- D GB7DJK-1 PC38^GB7DJK-1^~
769 <- D GB7DJK-1 PC18^ 1 nodes, 0 local / 1 total users Max users 0 Uptime
776 With later versions of Spider there is a set/login command for users. This
777 tells them when a user or node logs in or out. If you do not add a line to
778 your scripts after the final line (or before the client line which should always
779 be last if needed) then the login/logout information will be sent to users
780 <it>before</it> the login actually completes. This means if a node is
781 unreachable, it will continue sending logins and logouts to users even though it
782 is not actually connecting. To avoid this use the following line ...
789 In a script, this might look like ...
793 abort (Busy|Sorry|Fail)
794 connect telnet mary 3000
796 '>' 'telnet 44.131.93.96 7305'
803 Cluster links in particular suffer greatly from the presence of telnet echo.
804 This is caused by the telnet negotiation itself and can create at worst severe
805 loops. At best it creates unnecessary bandwidth and large logfiles! There are
806 things that can be done to limit this problem but will not always work dependent
807 on the route taken to connect.
810 Telnet echo itself should only be a problem if the connection is being made to
811 the telnet port (23). This port uses special rules that include echo negotiation.
812 If the connection is to a different port, such as 7300, this negotiation does
813 not happen and therefore no echo should be present.
816 Sometimes it is not possible to make a direct connection to another node and this
817 can cause problems. There is a way of trying to suppress the telnet echo but
818 this will not always work, unfortunately it is difficult to be more specific.
819 Here is an example of what I mean ...
823 abort (Busy|Sorry|Fail)
824 connect telnet mary.lancs.ac.uk
827 '\$' 'stty -echo raw'
828 '\$' 'telnet 44.131.93.96'
833 So, the first connection is made by Spider. This is fine as Spider uses the
834 Net_Telnet script from within perl. This actually uses TCP rather than TELNET
835 so no negotiation will be done on the first connection. Once connected to
836 mary.lancs.ac.uk, the command is sent to suppress echo. Now a telnet is made
837 to a cluster node that is accepting connections on port 23. The problem with
838 this link is that the negotiation is made by the remote machine, therefore you
839 have no control over it. The chances are that this link will create echo and
840 there will be no way you can stop it.
843 <sect1>Autostarting the cluster
846 Ok, you should now have DXSpider running nicely and allowing connects by cluster
847 nodes or users. However, it has to be shutdown and restarted manually. It
848 would be much easier to have it start automatically.
851 This is not only a way to start the cluster automatically, it also works as a
852 watchdog, checking the sanity of DXSpider and respawning it should it crash for
853 any reason. Before doing the following, shutdown the cluster as you did earlier.
856 Login as root and bring up the /etc/inittab file in your favourite editor. Add
857 the following lines to the file near the end ...
860 ##Start DXSpider on bootup and respawn it should it crash
861 DX:3:respawn:/bin/su -c "/usr/bin/perl -w /spider/perl/cluster.pl" sysop >/dev/tty7
865 This line works fine for RedHat distributions. It is also fine for SuSE up to
866 7.0. From Suse 7.1 you need to add runlevels 2 and 5 like this ...
869 DX:235:respawn:/bin/su -c "/usr/bin/perl -w /spider/perl/cluster.pl" sysop >/dev/tty7
873 The line required for Slackware distributions is slightly different. My thanks to
874 Aurelio, PA3EZL for this information.
877 DX:23:respawn:/bin/su - sysop -c "/usr/bin/perl -w /spider/perl/cluster.pl" >/dev/tty7
881 This will automatically start DXSpider on tty7 (ALT-F7) on bootup and restart
882 it should it crash for any reason.
885 As root type the command <em>telinit q</em>. DXSpider should start up
886 immediately. You will see the output on tty7 and if you login as <em>sysop</em>
887 you should find everything running nicely.
889 <sect>Microsoft Windows Installation
896 What you'll be left with once you've followed these instructions
897 is (hopefully) a working DX Spider v1.47 system that is capable
898 of accepting or originating "internet" connections, plus inbound
899 AX.25 and TCP/IP radio connections. If the absence of outbound
900 radio connections is a serious limitation for you, it would be
901 better for you to wait a couple more weeks until this support has
904 On the other hand, you may have an enquiring mind, or better yet,
905 may be looking for a useful way of connecting your current
906 (perhaps) AK1A cluster "to the internet" via some networking
907 mechanism (BPQEther, etc) or other. I won't be producing
908 instructions for the latter case, because I don't have an AK1A to
909 play with. But someone might ...
911 Whatever, this document is intended to get you started with DX
912 Spider in a Microsoft Windows ™ environment. It's not
913 intended to teach you anything other than how to perform a
914 minimum configuration of a DX Spider installation and have it
915 able to connect across "the internet" to other DX Clusters, while
916 accepting inbound TELNET and radio connections.
918 <sect1>The requirements
921 The very first things you're going to need are (in order of
925 <item>A cup of good, strong tea
926 <item>A supported Windows platform with an internet connection so you can
927 download the necessary software bits and bobs directly to it. There are other ways, but this is preferable.
928 <item>Another cup of good, strong tea
929 <item>If all goes according to plan, about an hour to spare
930 <item>Plenty of good, strong tea
936 The platform I used to generate these instructions was a
937 "vanilla" Microsoft Windows Me 4.90.3000 system, with a 700MHz
938 AMD Athlon processor and 96 Mb memory. I've also personally
939 verified that it runs on my laptop (Pentium 266MHz, 32 Mb memory,
940 Windows 98 SE v4.10.2222 A) and a computer that I assembled from
941 a random pile of junk (AMD K6-2 333MHz, 64 Mb memory, Windows 98
942 v4.10.1998). As a result, I have reason to believe that what I'm
943 about to describe will perform equally on any 32-bit MS Windows
944 environment with 32 Mb of memory.
946 Because of the changes that have recently been made to the core
947 "cluster.pl" module and the introduction of a very lightweight
948 "winclient.pl", I have a sneaking suspicion that this will now
949 run on any platform that has reasonably complete support for
950 Perl. Is there someone out there with both an enquiring mind and
951 (say) a Macintosh, for instance?
953 Please bear in mind, though, that my instructions relate solely
954 to how to get this going under a Microsoft Windows environment,
955 and I have zero intention of trying to make them say otherwise.
960 Install your chosen Perl environment. Unless you have a very good
961 reason for not doing so, I strongly suggest that you use
962 ActivePerl v5.6. For my testing & development, I used build 623.
963 You can get this from:- <htmlurl
964 url="http://www.activestate.com/Products/ActivePerl/Download.html"
965 name="http://www.activestate.com/Products/ActivePerl/Download.html">
967 You will need to choose either the MSI or the AS package. My
968 recommendation is that you choose the MSI package and deal with
969 the consequences if your system isn't equipped with support for
970 the latest MS Installer; you'll be better off in the long run.
971 The build 623 download is 7,460 KB, so now is a really good time
972 to have some tea if you're on a slow dial-up connection.
974 During installation, please ensure that you do choose the options
975 to "Add Perl to the PATH environment variable" and "Create Perl
976 file extension association"; it will make your life so much
977 easier. Once the installation is finished, be sure to reboot your
978 PC. You probably won't be told anywhere else that this needs to
979 be done now, but it does. Really.
981 Once you've rebooted, open a "DOS box" (Start > Run > command
982 might do it, if you can't find it elsewhere) and from wherever it
983 lands, type PERL -v <ENTER> (it's better if that's a lower-case
984 'v', because an upper-case 'V' means something else. You should
985 be rewarded with some interesting information about your Perl
986 installation. If you're not, you must go back to the beginning
987 and discover what went wrong and fix it. It's pointless to
988 proceed unless this simple check is passed. Assuming it did work,
991 <sect1>Additional packages
994 Some extensions ("packages") need to be added to the base Perl
995 distribution, and we'll do this next. If you're using the Perl I
996 recommended, and don't know any better for yourself, then just
997 blindly following these instructions will work just fine. If that
998 didn't describe you, then you're on your own.
1000 Visit the following URL:
1002 <htmlurl url="http://www.activestate.com/PPMPackages/zips/6xx-builds-only/"
1003 name="http://www.activestate.com/PPMPackages/zips/6xx-builds-only/">
1005 and download the following files:-
1015 Make yourself a convenient directory to unpack all of these zip
1016 files into (I put mine in "D:\ppm>") and do the following (the
1017 bits you type in are blue ). Note that where these files land
1018 will be directly related to where you chose to install your
1019 ActivePerl (mine, as you can probably guess from what follows,
1020 went into "D:\Perl"):-
1023 D:\ppm>ppm install Data-Dumper.ppd
1024 Installing package 'Data-Dumper.ppd'
1025 Installing D:\Perl\site\lib\auto\Data\Dumper\Dumper.bs
1026 Installing D:\Perl\site\lib\auto\Data\Dumper\Dumper.dll
1027 Installing D:\Perl\site\lib\auto\Data\Dumper\Dumper.exp
1028 Installing D:\Perl\site\lib\auto\Data\Dumper\Dumper.lib
1029 Installing D:\Perl\html\site\lib\auto\Data\Dumper\Dumper.html
1030 Installing D:\Perl\site\lib\Data\Dumper\Dumper.pm
1031 Writing D:\Perl\site\lib\auto\Data\Dumper\Dumper.packlist
1035 I'm not going to bother you with exhaustive details of the rest
1036 of them, but suffice it to say you need to:
1039 ppm install DB_File.ppd
1040 ppm install Net-Telnet.ppd
1041 ppm install TimeDate.ppd
1042 ppm install Time-HiRes.ppd
1045 If all that seemed to work OK, time to move along. Before anyone
1046 who is familiar with PPM tells me that we didn't need to download
1047 and keep those files locally, I knew that. I also knew that PPM
1048 is sometimes awkward to configure via firewalls, and that
1049 sometimes the repositories don't always work the way we'd hope. I
1050 do it that way because it suits me.
1052 <sect1>Getting Spider
1055 Get the current version of the DX Spider distribution. This needs
1056 to be v1.47 or later. You've got two ways (currently) of getting
1057 this; either get a CVS update from sourceforge (if you don't know
1058 what this is, then it isn't for you) or get my package from:-
1060 <htmlurl url="http://www.dcc.rsgb.org/WinSpider.zip" name="http://www.dcc.rsgb.org/WinSpider.zip">
1062 or if you want the lastest CVS version (which is produced every night)
1064 <htmlurl url="http://www.dxcluster.org/download/CVSlatest.tgz" name="http://www.dxcluster.org/download/CVSlatest.tgz">
1066 If you went down the CVS route, then everything will be nicely
1067 set out on your local disk. If you got the ZIP file, unpack it to
1068 somewhere convenient. The following examples assume that you put
1069 it on drive "C:\", for convenience.
1071 <bf>NOTE:</bf> This distribution method will go away as soon as the first
1072 v1.47 tarball is released. You can use WinZip to unpack that, and
1073 my life will be made easier by not needing to keep this .ZIP file
1076 <sect>Installing the software
1079 Ensure that your CVS session or your unZIPped file have left you
1080 with a directory "C:\spider\local"; if not, go to "C:\spider\"
1081 and create one. If "C:\spider" is missing, go back and figure out
1082 why, because it shouldn't be.
1084 Now create your own local copy of the DXVars.pm file by:-
1087 copy c:\spider\perl\DXVars.pm.issue
1088 c:\spider\local\DXVars.pm
1091 Now you'll need to edit this file using a text editor. If nothing
1092 else, you can simply
1104 to bring up an editor window containing the file. As an absolute
1105 minimum you must adjust the following items in DXVars.pm:-
1108 <item> $mycall - Should hold the callsign of your DX Cluster
1109 <item> $myname - The SysOp's first name
1110 <item> $myalias - the SysOp's callsign. Cannot be the same as $mycall!
1113 You really also ought to update the $mylatitude, $mylongitude,
1114 $myqth and $myemail variables. And unless you are absolutely
1115 certain you know what you're doing, you should change nothing
1118 <sect1>The AGW packet engine
1121 On the assumption that you'll be using the SV2AGW Packet Engine
1122 to interface your radios to the cluster, you should now create
1123 your own local copy of AGWConnect.pm by:-
1126 copy c:\spider\perl\AGWConnect.pm
1127 c:\spider\local\AGWConnect.pm
1133 notepad AGWConnect.pm
1136 to bring up an editor window containing the file. You must
1137 consider adjusting the following items in AGWConnect.pm:-
1140 <item>$enable - set to '1' to enable AGWPE interface
1141 <item>$login - the login ID you chose when you set up the SV2AGW security :-)
1142 <item>$passwd - password that matches $login
1145 <sect1>Setting up the initial user files
1148 Next you need to create the initial user files, etc. A tool is
1149 supplied which will do this for you. To run the tool:-
1153 perl create_sysop.pl
1156 If all goes according to plan, you will see no output from this
1157 program, and after a brief wait, your DOS prompt will be
1160 Depending on how brave you are, you might now care to try the
1167 If you did everything you were told, your DOS window will now
1168 hold a display which looks something like:-
1171 DXSpider DX Cluster Version 1.47
1172 Copyright (c) 1998-2001 Dirk Koopman G1TLH
1173 loading prefixes ...
1174 loading band data ...
1175 loading user file system ...
1176 starting listeners ...
1177 Internal port: localhost 27754
1179 reading in duplicate spot and WWV info ...
1180 reading existing message headers ...
1184 @msg = 0 before delete
1185 @msg = 0 after delete
1186 reading cron jobs ...v cron: reading /spider/cmd/crontab
1187 cron: adding 1 0 * * 0
1188 DXUser::export("$main::data/user_asc")
1189 reading database descriptors ...
1190 doing local initialisation ...
1191 orft we jolly well go ...
1195 Now, if that's what you've got, you are very nearly home and dry
1196 (in as far as these particular experiments are concerned, anyhow)
1198 To access your new cluster (from the local machine) find yourself another
1199 "DOS box" and do the following:-
1206 If you are rewarded with a display which looks something like:-
1209 Hello Iain, this is GB7SJP in Amersham, Bucks running DXSpider V1.47
1210 Cluster: 1 nodes, 1 local / 1 total users Max users 2 Uptime 0 00:00
1211 M0ADI de GB7SJP 4-Mar-2001 1511Z >
1214 You've arrived. Try some commands, and see how they feel. (In
1215 case you were wondering, "Iain", "M0ADI" and "GB7SJP" all came
1216 from the version of DXVars.pm that was on the machine when I
1217 started the winclient.pl)
1219 <sect1>Incoming telnets
1222 If you want to enable inbound "TELNET" connections, you've got a
1223 little more work to do. From a handy "DOS box" that's not doing
1224 anything else, do the following:-
1227 copy \spider\perl\listeners.pm \spider\local
1229 notepad listeners.pm
1232 The following lines need attention:-
1238 On my machine, I've simply uncommented the "0.0.0.0" entry by
1239 removing the '#' from the front of the line.
1241 If you don't have a static hostname for your machine, and you
1242 intend to allow folk to connect to your machine across the
1243 internet, then I'd suggest you pay a visit to www.dyndns.org and
1244 create one for yourself. While it's free, it will take a modest
1245 an amount of effort on your part to read, understand and
1246 implement what needs to be done to set this up.
1248 <sect1>Connecting to other clusters
1251 If you want to connect this to another cluster, then you'll want
1252 to negotiate a link with someone. For experimental purposes, I'm
1253 happy to allow folk to connect to GB7DXA (spud.ath.cx), on the
1254 understanding that the system may or may not be there and may or
1255 may not be connected to anything particularly useful at any given
1256 moment. Contact me by Email if you want me to set up a connection
1259 <sect>General Information
1262 The following relates to all versions of DXSpider and is not platform related.
1264 <sect1>The crontab file
1267 Login as <em>sysop</em> and create a file in /spider/local_cmd called crontab.
1268 Edit it with your favourite editor and add a line like this (I have included
1272 # check every 10 minutes to see if gb7xxx is connected and if not
1273 # start a connect job going
1275 0,10,20,30,40,50 * * * * start_connect('gb7xxx') unless connected('gb7xxx')
1279 The callsign involved will be the callsign of the cluster node you are
1280 going to connect to. This will now check every 10 minutes to see if
1281 gb7xxx is connected, if it is then nothing will be done. If it is not,
1282 then a connect attempt will be started.
1285 There are probably lots of other things you could use this crontab file for.
1286 If you want to know more about it, look at the
1287 <htmlurl url="http://www.dxcluster.org/cron.html" name="DXSpider"> website
1288 at the cron page where it is explained more fully.