1 <!doctype linuxdoc system>
\r
5 <!-- Title information -->
\r
7 <title>The DXSpider Administration Manual v1.50</title>
\r
8 <author>Ian Maude, G0VGS, (g0vgs@gb7mbc.net), and
\r
9 Charlie Carroll, K1XX, (k1xx@ptcnh.net)</author>
\r
10 <date>March 2003 revision 0.5</date>
\r
13 A reference for SysOps of the DXSpider DXCluster program.
\r
16 <!-- Table of contents -->
\r
19 <!-- Begin the document -->
\r
21 <sect>Routing and Filtering
\r
26 From DXSpider version 1.48, major changes were introduced to the way
\r
27 node connections are treated. This is part of an ongoing process to
\r
28 remove problems with loops and to enable talk and other functions to
\r
29 propagate across the whole of the worldwide cluster network. In fact,
\r
30 in a Spider network, it would be useful, perhaps even necessary to
\r
31 have loops. This would give real resilience to the network, meaning
\r
32 that if a link dropped, the information flow would simply come in and
\r
33 go out via a different route. Of course, we do not have a complete
\r
34 network of Spider nodes, there are other programs out there. Some of
\r
35 these do not have any protection from loops. Certainly AK1A does not
\r
36 handle loops well at all. It is therefore necessary to have some form
\r
37 of protection for these nodes.
\r
40 In fact DXSpider has had a simple system for some time which is called
\r
41 <it>isolation</it>. This is similar to what in other systems such as
\r
42 <bf>clx</bf>, is called <it>passive mode</it>. A more detailed explanation
\r
43 of <it>isolation</it> is given further below. This system is still available
\r
44 and, for simple networks, is probably all that you need.
\r
47 The new functionality introduced in version 1.48 allows filtering the node
\r
48 and user protocol frames on a "per interface" basis. We call this
\r
49 <it>route filtering</it>. This is used <bf>instead of</bf>
\r
50 <it>isolation</it>.
\r
53 What this really means is that you can control more or less completely
\r
54 which user and node management PC protocol frames pass to each of your
\r
55 partner nodes. You can also limit what comes into your node from your
\r
56 partners. It is even possible to control the settings that your partner
\r
57 node has for the routing information that it sends to you
\r
58 (using the <it>rcmd</it> command).
\r
60 <sect1>Route Filters
\r
63 Initially when route filters were being tested we generated a
\r
64 "default" filter. Unfortunately it quickly became apparent that this
\r
65 might suit the UK cluster network but didn't really fit anybody else.
\r
66 However using a default filter is an appropriate thing to do. How, is
\r
67 explained further on.
\r
70 The first thing that you must do is determine whether you need to use
\r
71 route filtering <bf>at all</bf>. If you are a "normal" node with two or
\r
72 three partners and you arranged in an "official" non-looping tree type
\r
73 network, then <bf>you do not need to do route filtering</bf> and you will
\r
74 feel a lot better for not getting involved. If you are successfully using
\r
75 <it>isolation</it> then you also probably don't need to use route filtering.
\r
78 To put it simply, you should not mix Isolation and Route Filtering. It
\r
79 will work, of sorts, but you will not get the expected results. If you
\r
80 are using Isolation sucessfully at the moment, do not get involved in
\r
81 Route Filtering unless you have a good supply of aspirin! Once you have
\r
82 started down the road of Route Filtering, do not use Isolation either.
\r
83 Use one or the other, not both.
\r
86 You will only require this functionality if you are "well-connected". What
\r
87 that means is that you are connected to several different parts of (say)
\r
88 the EU cluster and, at the same time, also connected to two or three places
\r
89 in the US which, in turn are connected back to the EU. This is called a
\r
90 "loop" and if you are seriously looped then you need filtering.
\r
93 I should at this stage give a little bit of background on filters. All
\r
94 the filters in Spider work in basically the same way. You can either
\r
95 accept or reject various options in order to create the filter rules
\r
96 you wish to achieve. Some filters are user settable, others can only
\r
97 be altered by the sysop. Route filtering can only be done by the sysop.
\r
100 Anyway, without further discouragement, let me start the process
\r
103 <sect1>The node_default filter
\r
106 All normal systems should have a default routing filter and it should
\r
107 usually be set to send only the normal, unlooped, view of your
\r
108 "national" network. Here in the UK that means nodes from the UK and
\r
109 Eire, in EU it is more complex as the networks there grew up in a more
\r
113 The generic commands are:-
\r
116 reject/route node_default <filter_option>
\r
120 accept/route node_default <filter_option>
\r
123 where filter_option is one of the following ...
\r
126 call <prefixes>
\r
127 call_dxcc <numbers>
\r
128 call_itu <numbers>
\r
129 call_zone <numbers>
\r
130 channel <prefixes>
\r
131 channel_dxcc <numbers>
\r
132 channel_itu <numbers>
\r
133 channel_zone <numbers>
\r
136 Please be careful if you alter this setting, it will affect
\r
137 <bf><it>ALL</it></bf> your links! Remember, this is a <it>default</it>
\r
138 filter for node connections, not a <it>per link</it> default.
\r
141 For the default routing filter then you have two real choices: either
\r
142 a "national" view or the "safe" option of only your own
\r
143 callsign. Examples of each (for my node: GB7DJK) are:-
\r
146 acc/route node_default call_dxcc 61,38
\r
147 acc/route node_default call gb7djk
\r
150 GB7DJK uses the first of these. The DXCC countries can be obtained from the
\r
151 <it>show/prefix</it> command.
\r
154 The example filters shown control <it>output</it> <bf>TO</bf> all your
\r
155 partner nodes unless they have a specific filter applied to them (see
\r
159 It is also possible to control the <it>incoming</it> routing
\r
160 information that you are prepared to accept <bf>FROM</bf> your partner
\r
161 nodes. The reason this is necessary is to make sure that stuff like
\r
162 mail, pings and similar commands a) go down the correct links and b)
\r
163 don't loop around excessively. Again using GB7DJK as an example a typical
\r
164 default input filter would be something like:
\r
167 rej/route node_default input call_dxcc 61,38 and not channel_dxcc 61,38
\r
170 What this does is accept node and user information for our national
\r
171 network from nodes that are in our national network, but rejects such
\r
172 information from anyone else. Although it doesn't explicitly say so,
\r
173 by implication, any other node information (not from the UK and Eire)
\r
177 As I imagine it will take a little while to get one's head around all of
\r
178 this you can study the effect of any rules that you try by watching the
\r
179 debug output after having done:-
\r
185 After you have got tired of that, to put it back the way it was:-
\r
191 <sect1>General route filtering
\r
194 Exactly the same rules apply for general route filtering. You would
\r
195 use either an accept filter or a reject filter like this ...
\r
198 reject/route <node_call> <filter_option>
\r
202 accept/route <node_call> <filter_option>
\r
206 Here are some examples of route filters ...
\r
209 rej/route gb7djk call_dxcc 61,38 (send everything except UK+EIRE nodes)
\r
210 rej/route all (equiv to [very] restricted mode)
\r
211 acc/route gb7djk call_dxcc 61,38 (send only UK+EIRE nodes)
\r
212 acc/route gb7djk call gb7djk (equiv to SET/ISOLATE)
\r
215 In practice you will either be opening the default filter out for a
\r
216 partner by defining a specific filter for that callsign:-
\r
219 acc/route gb7baa all
\r
220 acc/route gb7baa input all
\r
223 or restricting it quite a lot, in fact making it very nearly like an
\r
224 <it>isolated</it> node, like this:-
\r
227 acc/route pi4ehv-8 call gb7djk
\r
228 rej/route pi4ehv-8 input call_dxcc 61,38
\r
231 This last example takes everything except UK and Eire from PI4EHV-8
\r
232 but only sends him my local configuration (just a PC19 for GB7DJK and
\r
233 PC16s for my local users).
\r
236 It is possible to write <bf>much</bf> more complex rules, there are up
\r
237 to 10 accept/reject pairs per callsign per filter. For more information
\r
238 see the next section.
\r
241 <sect1>General filter rules
\r
244 Upto v1.44 it was not possible for the user to set their own filters. From
\r
245 v1.45 though that has all changed. It is now possible to set filters for just
\r
246 about anything you wish. If you have just updated from an older version of
\r
247 DXSpider you will need to update your new filters. You do not need to do
\r
248 anything with your old filters, they will be renamed as you update.
\r
251 There are 3 basic commands involved in setting and manipulating filters. These
\r
252 are <em>accept</em>, <em>reject</em> and <em>clear</em>. First we will look
\r
253 generally at filtering. There are a number of things you can filter in the
\r
254 DXSpider system. They all use the same general mechanism.
\r
257 In general terms you can create a "reject" or an "accept" filter which can have
\r
258 up to 10 lines in it. You do this using, for example ...
\r
265 where ..... are the specific commands for that type of filter. There are filters
\r
266 for spots, wwv, announce, wcy and (for sysops) connects. See each different
\r
267 accept or reject command reference for more details.
\r
269 There is also a command to clear out one or more lines in a filter. They are ...
\r
276 There is clear/xxxx command for each type of filter.
\r
279 and you can check that your filters have worked by the command ...
\r
286 For now we are going to use spots for the examples, but you can apply the same
\r
287 principles to all types of filter.
\r
289 <sect1>Types of filter
\r
292 There are two main types of filter, <em>accept</em> or <em>reject</em>. You
\r
293 can use either to achieve the result you want dependent on your own preference
\r
294 and which is more simple to do. It is pointless writing 8 lines of reject
\r
295 filters when 1 accept filter would do the same thing! Each filter has 10
\r
296 lines (of any length) which are tried in order. If a line matches then the
\r
297 action you have specified is taken (ie reject means ignore it and accept
\r
301 If you specify reject filters, then any lines that arrive that match the filter
\r
302 will be dumped but all else will be accepted. If you use an accept filter,
\r
303 then ONLY the lines in the filter will be accepted and all else will be dumped.
\r
304 For example if you have a single line <em>accept</em> filter ...
\r
307 accept/spots on vhf and (by_zone 14,15,16 or call_zone 14,15,16)
\r
310 then you will <em>ONLY</em> get VHF spots <em>from</em> or <em>to</em> CQ zones
\r
314 If you set a reject filter like this ...
\r
317 reject/spots on hf/cw
\r
320 Then you will get everything <em>EXCEPT</em> HF CW spots. You could make this
\r
321 single filter even more flexible. For example, if you are interested in IOTA
\r
322 and will work it even on CW even though normally you are not interested in
\r
323 CW, then you could say ...
\r
326 reject/spots on hf/cw and not info iota
\r
329 But in that case you might only be interested in iota and say:-
\r
332 accept/spots not on hf/cw or info iota
\r
335 which achieves exactly the same thing. You should choose one or the other
\r
336 until you are comfortable with the way it works. You can mix them if you
\r
337 wish (actually you can have an accept AND a reject on the same line) but
\r
338 don't attempt this until you are sure you know what you are doing!
\r
341 You can arrange your filter lines into logical units, either for your own
\r
342 understanding or simply convenience. Here is an example ...
\r
345 reject/spots 1 on hf/cw
\r
346 reject/spots 2 on 50000/1400000 not (by_zone 14,15,16 or call_zone 14,15,16)
\r
349 What this does is to ignore all HF CW spots and also rejects any spots on VHF
\r
350 which don't either originate or spot someone in Europe.
\r
353 This is an example where you would use a line number (1 and 2 in this case), if
\r
354 you leave the digit out, the system assumes '1'. Digits '0'-'9' are available.
\r
355 This make it easier to see just what filters you have set. It also makes it
\r
356 more simple to remove individual filters, during a contest for example.
\r
359 You will notice in the above example that the second line has brackets. Look
\r
360 at the line logically. You can see there are 2 separate sections to it. We
\r
361 are saying reject spots that are VHF or above <em>APART</em> from those in
\r
362 zones 14, 15 and 16 (either spotted there or originated there). If you did
\r
363 not have the brackets to separate the 2 sections, then Spider would read it
\r
364 logically from the front and see a different expression entirely ...
\r
367 (on 50000/1400000 and by_zone 14,15,16) or call_zone 14,15,16
\r
370 The simple way to remember this is, if you use OR - use brackets. Whilst we are
\r
371 here CASE is not important. 'And BY_Zone' is just the same as 'and by_zone'.
\r
373 As mentioned earlier, setting several filters can be more flexible than
\r
374 simply setting one complex one. Doing it in this way means that if you want
\r
375 to alter your filter you can just redefine or remove one or more lines of it or
\r
376 one line. For example ...
\r
379 reject/spots 1 on hf/ssb
\r
382 would redefine our earlier example, or
\r
388 To remove all the filter lines in the spot filter ...
\r
394 <sect1>Filter options
\r
397 You can filter in several different ways. The options are listed in the
\r
398 various helpfiles for accept, reject and filter.
\r
400 <sect1>Default filters
\r
403 Sometimes all that is needed is a general rule for node connects. This can
\r
404 be done with a node_default filter. This rule will always be followed, even
\r
405 if the link is isolated, unless another filter is set specifically. Default
\r
406 rules can be set for nodes and users. They can be set for spots, announces,
\r
407 WWV and WCY. They can also be used for hops. An example might look like
\r
411 accept/spot node_default by_zone 14,15,16,20,33
\r
412 set/hops node_default spot 50
\r
415 This filter is for spots only, you could set others for announce, WWV and WCY.
\r
416 This filter would work for ALL nodes unless a specific filter is written to
\r
417 override it for a particular node. You can also set a user_default should
\r
418 you require. It is important to note that default filters should be
\r
419 considered to be "connected". By this I mean that should you override the
\r
420 default filter for spots, you need to add a rule for the hops for spots also.
\r
422 <sect1>Advanced filtering
\r
425 Once you are happy with the results you get, you may like to experiment.
\r
428 The previous example that filters hf/cw spots and accepts vhf/uhf spots from EU
\r
429 can be written with a mixed filter, for example ...
\r
433 acc/spot on 0/30000
\r
434 acc/spot 2 on 50000/1400000 and (by_zone 14,15,16 or call_zone 14,15,16)
\r
437 Note that the first filter has not been specified with a number. This will
\r
438 automatically be assumed to be number 1. In this case, we have said <em>reject all
\r
439 HF spots in the CW section of the bands but accept all others at HF. Also
\r
440 accept anything in VHF and above spotted in or by operators in the zones
\r
441 14, 15 and 16</em>. Each filter slot actually has a 'reject' slot and
\r
442 an 'accept' slot. The reject slot is executed BEFORE the accept slot.
\r
445 It was mentioned earlier that after a reject test that doesn't match, the default
\r
446 for following tests is 'accept', the reverse is true for 'accept'. In the example
\r
447 what happens is that the reject is executed first, any non hf/cw spot is passed
\r
448 to the accept line, which lets through everything else on HF. The next filter line
\r
449 lets through just VHF/UHF spots from EU.
\r
451 <sect1>Basic hop control
\r
454 In /spider/data you will find a file called hop_table.pl. This is the file
\r
455 that controls your hop count settings. It has a set of default hops on the
\r
456 various PC frames and also a set for each node you want to alter the hops for.
\r
457 You may be happy with the default settings of course, but this powerful tool
\r
458 can help to protect and improve the network. The file will look something
\r
463 # hop table construction
\r
468 # default hopcount to use
\r
471 # some variable hop counts based on message type
\r
482 # the per node hop control thingy
\r
487 GB7ADX => { 11 => 8,
\r
495 GB7UDX => { 11 => 8,
\r
514 Each set of hops is contained within a pair of curly braces and contains a
\r
515 series of PC frame types. PC11 for example is a DX spot. The figures here
\r
516 are not exhaustive but should give you a good idea of how the file works.
\r
519 SHould any of the nodecalls include an ssid, it is important to wrap the
\r
520 whole call in single quotes, like this ...
\r
533 If you do not do this, you will get errors and the file will not work as
\r
537 You can alter this file at any time, including whilst the cluster is running.
\r
538 If you alter the file during runtime, the command <em>load/hops</em> will
\r
539 bring your changes into effect.
\r
541 <sect1>Hop Control on Specific Nodes
\r
543 <p>You can set a callsign specific hop count for any of the standard filter
\r
547 set/hops gb7djk spot 4
\r
548 set/hops node_default route 10
\r
549 set/hops gb7baa wcy 5
\r
552 all work on their specific area of the protocol.
\r
555 The <em>set/hops</em> command overrides any hops that you have set otherwise.
\r
558 You can show what hops have been set using the <em>show/hops</em> command.
\r
560 <sect1>Isolating networks
\r
563 It is possible to isolate networks from each other on a "gateway" node using the
\r
564 <em>set/isolate <node_call></em> command.
\r
567 The effect of this is to partition an isolated network completely from another
\r
568 node connected to your node. Your node will appear on and otherwise behave
\r
569 normally on every network to which you are connected, but data from an isolated
\r
570 network will not cross onto any other network or vice versa. However all the
\r
571 spot, announce and WWV traffic and personal messages will still be handled
\r
572 locally (because you are a real node on all connected networks), that is locally
\r
573 connected users will appear on all networks and will be able to access and
\r
574 receive information from all networks transparently. All routed messages will
\r
575 be sent as normal, so if a user on one network knows that you are a gateway for
\r
576 another network, he can still still send a talk/announce etc message via your
\r
577 node and it will be routed across.
\r
580 If you use isolate on a node connection you will continue to receive
\r
581 all information from the isolated partner, however you will not pass
\r
582 any information back to the isolated node. There are times when you
\r
583 would like to forward only spots across a link (maybe during a contest
\r
584 for example). To do this, isolate the node in the normal way and use
\r
585 an <em>acc/spot >call< all</em> filter to override the isolate.
\r
587 <sect>Other filters
\r
589 <sect1>Filtering Mail
\r
592 In the /spider/msg directory you will find a file called badmsg.pl.issue. Rename
\r
593 this to badmsg.pl and edit the file. The original looks something like this ....
\r
597 # the list of regexes for messages that we won't store having
\r
598 # received them (bear in mind that we must receive them fully before
\r
602 # The format of each line is as follows
\r
604 # type source pattern
\r
605 # P/B/F T/F/O/S regex
\r
607 # type: P - private, B - bulletin (msg), F - file (ak1a bull)
\r
608 # source: T - to field, F - from field, O - origin, S - subject
\r
609 # pattern: a perl regex on the field requested
\r
611 # Currently only type B and P msgs are affected by this code.
\r
613 # The list is read from the top down, the first pattern that matches
\r
614 # causes the action to be taken.
\r
616 # The pattern can be undef or 0 in which case it will always be selected
\r
617 # for the action specified
\r
625 'B', 'T', 'WANTED',
\r
626 'B', 'S', 'WANTED',
\r
635 I think this is fairly self explanatory. It is simply a list of subject
\r
636 headers that we do not want to pass on to either the users of the cluster or
\r
637 the other cluster nodes that we are linked to. This is usually because of
\r
638 rules and regulations pertaining to items for sale etc in a particular country.
\r
641 <sect1>Filtering words from text fields in Announce, Talk and DX spots
\r
644 From version 1.48 onwards the interface to this has changed. You can now
\r
645 use the commands <em>set/badword</em> to add words that you are not prepared
\r
646 to see on the cluster, <em>unset/badword</em> to allow that word again and
\r
647 <em>show/badword</em> to list the words that you have set.
\r
650 If you have a previous <em>/spider/data/badwords</em>, the first time you start
\r
651 the node, it will read and convert this file to the new commands. The old style
\r
652 file will then be removed.
\r
654 <sect1>Stopping (possibly bad) DX Spots from Nodes or Spotters
\r
657 There are a number of commands that control whether a spot progresses
\r
658 any further by regarding it as "bad" in some way.
\r
661 A DX Spot has a number of fields which can be checked to see whether they
\r
662 contain "bad" values, they are: the DX callsign itself, the Spotter and
\r
663 the Originating Node.
\r
666 There are a set of commands which allow the sysop to control whether a
\r
675 These work in the same as the <em>set/badword</em> command, you can add
\r
676 any words or callsigns or whatever to the appropriate database. For
\r
677 example, to stop a spot from a particular node you do:
\r
680 set/badnode gb7djk gb7dxc
\r
686 set/badspotter b0mb p1rat nocall
\r
692 set/baddx video wsjt
\r
695 You can remove a word using the appropriate unset command
\r
696 (<em>unset/baddx, unset/badspotter, unset/badnode</em>) or list them
\r
697 using one of <em>show/baddx, show/badspotter</em> and
\r
698 <em>show/badnode</em>.
\r
703 DXSpider deals seamlessly with standard AK1A type mail. It supports both
\r
704 personal and bulletin mail and the sysop has additional commands to ensure
\r
705 that mail gets to where it is meant. DXSpider will send mail almost
\r
706 immediately, assuming that the target is on line. However, only one
\r
707 mail message is dealt with at any one time. If a mail message is already
\r
708 being sent or recieved, then the new message will be queued until it has
\r
711 The cluster mail is automatically deleted after 30 days unless the sysop
\r
712 sets the "keep" flag using the <em>msg</em> command.
\r
714 <sect1>Personal mail
\r
717 Personal mail is sent using the <em>sp</em> command. This is actually the
\r
718 default method of sending mail and so a simple <em>s</em> for send will do.
\r
719 A full list of the send commands and options is in the <em>command set</em>
\r
720 section, so I will not duplicate them here.
\r
722 <sect1>Bulletin mail
\r
725 Bulletin mail is sent by using the <em>sb</em> command. This is one of the
\r
726 most common mistakes users make when sending mail. They send a bulletin
\r
727 mail with <em>s</em> or <em>sp</em> instead of <em>sb</em> and of course
\r
728 the message never leaves the cluster. This can be rectified by the sysop
\r
729 by using the <em>msg</em> command.
\r
731 <P>Bulletin addresses can be set using the Forward.pl file.
\r
736 DXSpider receives all and any mail sent to it without any alterations needed
\r
737 in files. Because personal and bulletin mail are treated differently, there
\r
738 is no need for a list of accepted bulletin addresses. It is necessary, however,
\r
739 to tell the program which links accept which bulletins. For example, it is
\r
740 pointless sending bulletins addresses to "UK" to any links other than UK
\r
741 ones. The file that does this is called forward.pl and lives in /spider/msg.
\r
742 At default, like other spider files it is named forward.pl.issue. Rename it
\r
743 to forward.pl and edit the file to match your requirements.
\r
744 The format is below ...
\r
748 # this is an example message forwarding file for the system
\r
750 # The format of each line is as follows
\r
752 # type to/from/at pattern action destinations
\r
753 # P/B/F T/F/A regex I/F [ call [, call ...] ]
\r
755 # type: P - private, B - bulletin (msg), F - file (ak1a bull)
\r
756 # to/from/at: T - to field, F - from field, A - home bbs, O - origin
\r
757 # pattern: a perl regex on the field requested
\r
758 # action: I - ignore, F - forward
\r
759 # destinations: a reference to an array containing node callsigns
\r
761 # if it is non-private and isn't in here then it won't get forwarded
\r
763 # Currently only type B msgs are affected by this code.
\r
765 # The list is read from the top down, the first pattern that matches
\r
766 # causes the action to be taken.
\r
768 # The pattern can be undef or 0 in which case it will always be selected
\r
769 # for the action specified
\r
771 # If the BBS list is undef or 0 and the action is 'F' (and it matches the
\r
772 # pattern) then it will always be forwarded to every node that doesn't have
\r
773 # it (I strongly recommend you don't use this unless you REALLY mean it, if
\r
774 # you allow a new link with this on EVERY bull will be forwarded immediately
\r
775 # on first connection)
\r
781 'B', 'T', 'LOCAL', 'F', [ qw(GB7MBC) ],
\r
782 'B', 'T', 'ALL', 'F', [ qw(GB7BAA GB7ADX PA4AB-14) ],
\r
783 'B', 'T', 'UK', 'F', [ qw(GB7BAA GB7ADX) ],
\r
784 'B', 'T', 'QSL', 'F', [ qw(GB7BAA GB7ADX PA4AB-14) ],
\r
785 'B', 'T', 'QSLINF', 'F', [ qw(GB7BAA GB7ADX PA4AB-14) ],
\r
786 'B', 'T', 'DX', 'F', [ qw(GB7BAA GB7ADX PA4AB-14) ],
\r
787 'B', 'T', 'DXINFO', 'F', [ qw(GB7BAA GB7ADX PA4AB-14) ],
\r
788 'B', 'T', 'DXNEWS', 'F', [ qw(GB7BAA GB7ADX PA4AB-14) ],
\r
789 'B', 'T', 'DXQSL', 'F', [ qw(GB7BAA GB7ADX PA4AB-14) ],
\r
790 'B', 'T', 'SYSOP', 'F', [ qw(GB7BAA GB7ADX) ],
\r
791 'B', 'T', '50MHZ', 'F', [ qw(GB7BAA GB7ADX PA4AB-14) ],
\r
795 Simply insert a bulletin address and state in the brackets where you wish
\r
796 that mail to go. For example, you can see here that mail sent to "UK" will
\r
797 only be sent to the UK links and not to PA4AB-14.
\r
800 To force the cluster to reread the file use load/forward
\r
803 NB: If a user tries to send mail to a bulletin address that does not exist
\r
804 in this file, they will get an error.
\r
806 <sect1>The msg command
\r
809 The <em>msg</em> command is a very powerful and flexible tool for the
\r
810 sysop. It allows the sysop to alter to and from fields and make other
\r
811 changes to manage the cluster mail.
\r
813 Here is a full list of the various options ...
\r
816 MSG TO <msgno> <call> - change TO callsign to <call>
\r
817 MSG FRom <msgno> <call> - change FROM callsign to <call>
\r
818 MSG PRrivate <msgno> - set private flag
\r
819 MSG NOPRrivate <msgno> - unset private flag
\r
820 MSG RR <msgno> - set RR flag
\r
821 MSG NORR <msgno> - unset RR flag
\r
822 MSG KEep <msgno> - set the keep flag (message won't be deleted ever)
\r
823 MSG NOKEep <msgno> - unset the keep flag
\r
824 MSG SUbject <msgno> <new> - change the subject to <new>
\r
825 MSG WAittime <msgno> - remove any waiting time for this message
\r
826 MSG NOREad <msgno> - mark message as unread
\r
827 MSG REad <msgno> - mark message as read
\r
828 MSG QUeue - queue any outstanding bulletins
\r
829 MSG QUeue 1 - queue any outstanding private messages
\r
832 These commands are simply typed from within the cluster as the sysop user.
\r
834 <sect1>Message status
\r
837 You can check on a message from within the cluster by using the command
\r
838 <em>stat/msg</em>. This will give you additional information on the
\r
839 message number including which nodes have received it, which node it
\r
840 was received from and when etc. Here is an example of the output of
\r
844 G0VGS de GB7MBC 28-Jan-2001 1308Z >
\r
847 Msg Time: 26-Jan-2001 1302Z
\r
851 Subject: AMSAT 2line KEPS 01025.AMSAT
\r
853 Got it Nodes: GB7BAA, GB7ADX
\r
857 G0VGS de GB7MBC 28-Jan-2001 1308Z >
\r
860 <sect1>Filtering mail
\r
863 This is described in the section on <em>Other filters</em> so I will not
\r
866 <sect1>Distribution lists
\r
869 Distribution lists are simply a list of users to send certain types of
\r
870 mail to. An example of this is mail you only wish to send to other
\r
871 sysops. In /spider/msg there is a directory called <em>distro</em>. You
\r
872 put any distibution lists in here. For example, here is a file called
\r
873 SYSOP.pl that caters for the UK sysops.
\r
876 qw(GB7TLH GB7DJK GB7DXM GB7CDX GB7BPQ GB7DXN GB7MBC GB7MBC-6 GB7MDX
\r
877 GB7NDX GB7SDX GB7TDX GB7UDX GB7YDX GB7ADX GB7BAA GB7DXA GB7DXH
\r
878 GB7DXK GB7DXI GB7DXS)
\r
881 Any mail sent to "sysop" would only be sent to the callsigns in this list.
\r
883 <sect1>BBS interface
\r
886 Spider provides a simple BBS interface. No input is required from the sysop
\r
887 of the cluster at all. The BBS simply sets the cluster as a BBS and pushes
\r
888 any required mail to the cluster. No mail can flow from Spider to the BBS,
\r
889 the interface is one-way.
\r
892 Please be careful not to flood the cluster network with unnecessary mail.
\r
893 Make sure you only send mail to the clusters that want it by using the
\r
894 Forward.pl file very carefully.
\r
899 From 1.48 onwards it will become increasingly possible to control DXSpider's
\r
900 operation with scripts of various kinds.
\r
903 The directory /spider/scripts is where it all happens and is used for several
\r
904 things. Firstly it contains a file called startup that can be used to call
\r
905 in any changes to the cluster from the default settings on startup. This
\r
906 script is executed immediately after all initialisation of the node is done
\r
907 but before any connections are possible. Examples of this include how many
\r
908 spots it is possible to get with the sh/dx command, whether you want
\r
909 registration/passwords to be permanently on etc. An example file is shown
\r
910 below and is included in the distribution as startup.issue.
\r
914 # startup script example
\r
916 # set maximum no of spots allowed to 100
\r
917 # set/var $Spot::maxspots = 100
\r
919 # Set registration on
\r
920 # set/var $main::reqreg = 1
\r
923 # set/var $main::passwdreq = 1
\r
928 As usual, any text behind a # is treated as a comment and not read. To use
\r
929 this file, simply rename it from startup.issue to startup. In our example
\r
930 above there are three options. The first option is the amount of spots that
\r
931 a user can request with the <em>sh/dx</em> command. Normally the default is
\r
932 to give 10 spots unless the user specifies more. Without this line enabled,
\r
933 the maximum a user can request is 100 spots. Depending on your link quality
\r
934 you may wish to enable more or less by specifying the number.
\r
937 The other 2 options are dealt with more fully in the security section.
\r
940 Secondly, it is used to store the login scripts for users and nodes. Currently
\r
941 this can only be done by the sysop but it is envisaged that eventually users will
\r
942 be able to set their own. An example is included in the distibution but here is
\r
958 The lines in between commands can simply insert a blank line or a character
\r
959 such as a + sign to make the output easier to read. Simply create this script
\r
960 with your favourite editor and save it with the callsign of the user as the
\r
961 filename. Filenames should always be in lower case.
\r
964 Commands can be inserted in the same way for nodes. A node may wish a series
\r
965 of commands to be issued on login, such as a merge command for example.
\r
968 Thirdly, there are 2 default scripts for users and nodes who do not have a
\r
969 specifically defined script. These are <em>user_default</em> and
\r
970 <em>node_default</em>
\r
975 Spider allows the creation of local or remote databases. It supports
\r
976 chained databases, allowing several different databases to be scanned
\r
977 with one simple command. Importing of databases is limited at present
\r
978 to the standard AK1A databases such as OBLAST and the DB0SDX QSL
\r
979 database but will expand with time.
\r
981 <sect1>Creating databases
\r
984 Creating a database could not be more simple. All the commands are
\r
985 sent from the cluster prompt as the <em>sysop</em> user.
\r
987 To create a database you use the command <em>dbcreate</em>. It can
\r
988 be used in 3 different ways like so ..
\r
994 To simply create a database locally, you just tell the command the
\r
995 name of the database. This does not create the actual database, it
\r
996 simply defines it to say that it exists.
\r
999 dbcreate <name> chain <name> [<name>...]
\r
1002 This creates a chained database entry. The first database will be
\r
1003 scanned, then the second, the third etc...
\r
1006 dbcreate <name> remote <name>
\r
1009 This creates a remote entry. the first name field is the database
\r
1010 name at the remote node, then the remote switch, then the actual
\r
1011 node_call of the remote node, for example...
\r
1014 dbcreate buckmaster remote gb7dxc
\r
1017 Remote databases cannot be chained, however, the last database in a
\r
1018 chain can be a remote database.
\r
1020 <sect1>Importing databases
\r
1023 The only databases that Spider can currently import are the standard
\r
1024 AK1A databases such as OBLAST or the DB0SDX qsl and address database.
\r
1025 This will be added to with time.
\r
1027 To import such a database, first put the file somewhere useful like /tmp
\r
1028 and then issue the following command ...
\r
1031 dbimport oblast /tmp/OBLAST.FUL
\r
1034 This will update the existing local oblast database or create it if
\r
1035 it does not exist.
\r
1037 <sect1>Checking available databases
\r
1040 Once a database is created, you will want to check that it has been
\r
1041 added. To do this use the <em>dbavail</em> command. This will
\r
1042 output the available databases. For example ...
\r
1046 DB Name Location Chain
\r
1050 G0VGS de GB7MBC 3-Feb-2001 1925Z >
\r
1053 <sect1>Looking up databases
\r
1056 To look for information in a defined database, simply use the <em>dbshow</em>
\r
1057 command, for example ...
\r
1060 dbshow buckmaster G0YLM
\r
1063 will show the information for the callsign G0YLM from the buckmaster
\r
1064 database if it exists. To make things more standard for the users
\r
1065 you can add an entry in the Aliases file so that it looks like a standard
\r
1066 <em>show</em> command like this ...
\r
1069 '^sh\w*/buc', 'dbshow buckmaster', 'dbshow',
\r
1072 Now you can simply use show/buckmaster or an abreviation.
\r
1074 <sect1>Removing databases
\r
1077 To delete an existing database you use the <em>dbremove</em> command.
\r
1084 would remove the oblast database and its associated datafile from the
\r
1085 system. There are no warnings or recovery possible from this command.
\r
1086 If you remove a database it ceases to exist and would have to be created
\r
1087 from scratch if you still required it.
\r
1089 <sect>Information, files and useful programs
\r
1094 One of the more important things a cluster sysop needs to do is to get
\r
1095 information to his users. The simplest way to do this is to have a banner
\r
1096 that is sent to the user on login. This is know as a "message of the day"
\r
1097 or "motd". To set this up, simply create a file in /spider/data called motd
\r
1098 and edit it to say whatever you want. It is purely a text file and will be
\r
1099 sent automatically to anyone logging in to the cluster.
\r
1104 This message of the day file lives in the same directory as the standard
\r
1105 motd file but is only sent to non-registered users. Once registered they
\r
1106 will receive the same message as any other user.
\r
1108 <sect1>Downtime message
\r
1111 If for any reason the cluster is down, maybe for upgrade or maintenance but
\r
1112 the machine is still running, a message can be sent to the user advising them
\r
1113 of the fact. This message lives in the /spider/data directory and is called
\r
1114 "offline". Simply create the file and edit it to say whatever you wish.
\r
1115 This file will be sent to a user attempting to log into the cluster when
\r
1116 DXSpider is not actually running.
\r
1118 <sect1>Other text messages
\r
1121 You can set other text messages to be read by the user if they input the file
\r
1122 name. This could be for news items or maybe information for new users.
\r
1123 To set this up, make a directory under /spider called <em>packclus</em>.
\r
1124 Under this directory you can create files called <em>news</em> or <em>newuser</em>
\r
1125 for example. In fact you can create files with any names you like. These can
\r
1126 be listed by the user with the command ....
\r
1132 They can be read by the user by typing the command ....
\r
1138 If the file they want to read is called <em>news</em>. You could also set
\r
1139 an alias for this in the Alias file to allow them just to type <em>news</em>
\r
1142 You can also store other information in this directory, either directly or
\r
1143 nested under directories. One use for this would be to store DX bulletins
\r
1144 such as the OPDX bulletins. These can be listed and read by the user.
\r
1145 To keep things tidy, make a directory under /spider/packclus called
\r
1146 <em>bulletin</em>. Now copy any OPDX or similar bulletins into it. These
\r
1147 can be listed by the user in the same way as above using the <em>show/files</em>
\r
1148 command with an extension for the bulletin directory you have just created,
\r
1152 show/files bulletin
\r
1156 An example would look like this ....
\r
1160 bulletin DIR 20-Dec-1999 1715Z news 1602 14-Dec-1999 1330Z
\r
1163 You can see that in the files area (basically the packclus directory) there is a
\r
1164 file called <em>news</em> and a directory called <em>bulletin</em>. You can
\r
1165 also see that dates they were created. In the case of the file <em>news</em>,
\r
1166 you can also see the time it was last modified, a good clue as to whether the
\r
1167 file has been updated since you last read it. To read the file called
\r
1168 <em>news</em> you would simply issue the command ....
\r
1174 To look what is in the bulletin directory you issue the command ....
\r
1177 show/files bulletin
\r
1178 opdx390 21381 29-Nov-1999 1621Z opdx390.1 1670 29-Nov-1999 1621Z
\r
1179 opdx390.2 2193 29-Nov-1999 1621Z opdx391 25045 29-Nov-1999 1621Z
\r
1180 opdx392 35969 29-Nov-1999 1621Z opdx393 15023 29-Nov-1999 1621Z
\r
1181 opdx394 33429 29-Nov-1999 1621Z opdx394.1 3116 29-Nov-1999 1621Z
\r
1182 opdx395 24319 29-Nov-1999 1621Z opdx396 32647 29-Nov-1999 1621Z
\r
1183 opdx396.1 5537 29-Nov-1999 1621Z opdx396.2 6242 29-Nov-1999 1621Z
\r
1184 opdx397 18433 29-Nov-1999 1621Z opdx398 19961 29-Nov-1999 1621Z
\r
1185 opdx399 17719 29-Nov-1999 1621Z opdx400 19600 29-Nov-1999 1621Z
\r
1186 opdx401 27738 29-Nov-1999 1621Z opdx402 18698 29-Nov-1999 1621Z
\r
1187 opdx403 24994 29-Nov-1999 1621Z opdx404 15685 29-Nov-1999 1621Z
\r
1188 opdx405 13984 29-Nov-1999 1621Z opdx405.1 4166 29-Nov-1999 1621Z
\r
1189 opdx406 28934 29-Nov-1999 1621Z opdx407 24153 29-Nov-1999 1621Z
\r
1190 opdx408 15081 29-Nov-1999 1621Z opdx409 23234 29-Nov-1999 1621Z
\r
1191 Press Enter to continue, A to abort (16 lines) >
\r
1194 You can now read any file in this directory using the type command, like this ....
\r
1197 type bulletin/opdx391
\r
1198 Ohio/Penn DX Bulletin No. 391
\r
1199 The Ohio/Penn Dx PacketCluster
\r
1200 DX Bulletin No. 391
\r
1203 Editor Tedd Mirgliotta, KB8NW
\r
1204 Provided by BARF-80 BBS Cleveland, Ohio
\r
1205 Online at 440-237-8208 28.8k-1200 Baud 8/N/1 (New Area Code!)
\r
1206 Thanks to the Northern Ohio Amateur Radio Society, Northern Ohio DX
\r
1207 Association, Ohio/Penn PacketCluster Network, K1XN & Golist, WB2RAJ/WB2YQH
\r
1208 & The 59(9) DXReport, W3UR & The Daily DX, K3TEJ, KN4UG, W4DC, NC6J, N6HR,
\r
1209 Press Enter to continue, A to abort (508 lines) >
\r
1212 The page length will of course depend on what you have it set to!
\r
1214 <sect1>The Aliases file
\r
1217 You will find a file in /spider/cmd/ called Aliases. This is the file that
\r
1218 controls what a user gets when issuing a command. It is also possible to
\r
1219 create your own aliases for databases and files you create locally.
\r
1222 You should not alter the original file in /spider/cmd/ but create a new file
\r
1223 with the same name in /spider/local_cmd. This means that any new Aliases files
\r
1224 that is downloaded will not overwrite your self created Aliases and also that
\r
1225 you do not override any new Aliases with your copy in /spider/local_cmd/. You
\r
1226 must remember that any files you store in /spider/local/ or /spider/local_cmd
\r
1227 override the originals if the same lines are used in both files.
\r
1230 The best way of dealing with all this then is to only put your own locally
\r
1231 created Aliases in the copy in /spider/local_cmd. The example below is
\r
1232 currently in use at GB7MBC.
\r
1237 # Local Aliases File
\r
1244 '^news$', 'type news', 'type',
\r
1247 '^sh\w*/buck$', 'show/qrz', 'show',
\r
1248 '^sh\w*/hftest$', 'dbshow hftest', 'dbshow',
\r
1249 '^sh\w*/qsl$', 'dbshow qsl', 'dbshow',
\r
1250 '^sh\w*/vhf$', 'dbshow vhf', 'dbshow',
\r
1251 '^sh\w*/vhftest$', 'dbshow vhftest', 'dbshow',
\r
1258 Each alphabetical section should be preceded by the initial letter and the section
\r
1259 should be wrapped in square brackets as you can see. The syntax is straightforward.
\r
1260 The first section on each line is the new command that will be allowed once the
\r
1261 alias is included. The second section is the command it is replacing and the last
\r
1262 section is the actual command that is being used.
\r
1265 The eagle-eyed amongst you will have noticed that in the first section, the new
\r
1266 alias command has a '^' at the start and a '$' at the end. Basically these force
\r
1267 a perfect match on the alias. The '^' says match the beginning exactly and the
\r
1268 '$' says match the end exactly. This prevents unwanted and unintentional matches
\r
1269 with similar commands.
\r
1272 I have 3 different types of alias in this file. At the top is an alias for 'news'.
\r
1273 This is a file I have created in the /spider/packclus/ directory where I can inform
\r
1274 users of new developments or points of interest. In it's initial form a user would
\r
1275 have to use the command <em>type news</em>. The alias allows them to simply type
\r
1276 <em>news</em> to get the info. Second is an alias for the <em>show/qrz</em>
\r
1277 command so that those users used to the original <em>show/buck</em> command in
\r
1278 AK1A will not get an error, and the rest of the lines are for locally created
\r
1279 databases so that a user can type <em>show/hftest</em> instead of having to use
\r
1280 the command <em>dbshow hftest</em> which is not as intuitive.
\r
1283 This file is just an example and you should edit it to your own requirements.
\r
1284 Once created, simply issue the command <em>load/alias</em> at the cluster
\r
1285 prompt as the sysop user and the aliases should be available.
\r
1291 In later versions of Spider a simple console program is provided for the sysop.
\r
1292 This has a type ahead buffer with line editing facilities and colour for spots,
\r
1293 announces etc. To use this program, simply use console.pl instead of client.
\r
1296 To edit the colours, copy /spider/perl/Console.pl to /spider/local and edit the
\r
1297 file with your favourite editor.
\r
1299 <sect1>Updating kepler data
\r
1302 Spider has a powerful and flexible show/satellite command. In order for
\r
1303 this to be accurate, the kepler data has to be updated regularly. In
\r
1304 general, this data is available as an email or via cluster mail.
\r
1305 Updating it is simple. First you need to export the mail message as a
\r
1306 file. You do this with the <em>export</em> command from the cluster prompt
\r
1307 as the sysop. For example ...
\r
1310 export 5467 /spider/perl/keps.in
\r
1314 would export message number 5467 as a file called keps.in in the
\r
1315 /spider/perl directory.
\r
1318 Now login to a VT as sysop and cd /spider/perl. There is a command in
\r
1319 the perl directory called <em>convkeps.pl</em>. All we need to do now is
\r
1320 convert the file like so ...
\r
1323 ./convkeps.pl keps.in
\r
1327 Now go back to the cluster and issue the command ...
\r
1334 That is it! the kepler data has been updated.
\r
1336 <sect1>The QRZ callbook
\r
1339 The command <em>sh/qrz</em> will only work once you have followed a few
\r
1340 simple steps. First you need to get a user ID and password from qrz.com.
\r
1341 Simply go to the site and create one. Secondly you need to copy the file
\r
1342 /spider/perl/Internet.pm to /spider/local and alter it to match your user
\r
1343 ID and password. You also at this point need to set $allow=1 to complete
\r
1344 the setup. Many thanks to Fred Lloyd, the proprieter of
\r
1345 <htmlurl url="http://www.qrz.com" name="qrz.com"> for allowing this access.
\r
1347 <sect1>Connecting logging programs
\r
1350 There appear to be very few logging programs out there that support telnet
\r
1351 especially the popular ones like LogEQF, Turbolog etc. This can make it
\r
1352 difficult to connect to your own cluster!
\r
1353 The way to do it is to make the logging program think it has a TNC attached
\r
1354 to a com port on the logging PC and 'push' a linux login out to it.
\r
1355 This is achieved very simply by the use of <em>agetty</em>.
\r
1358 All that is required is to add a line in /etc/inittab to have the client
\r
1359 ready for a connection on the com port of your choice. Remember that in
\r
1360 Linux, the com ports start at ttyS0 for com1, ttyS1 for com2 etc.
\r
1363 c4:2345:respawn:/sbin/agetty -L 9600 ttyS1
\r
1367 Add this after the standard runlevel lines in /etc/inittab. The above
\r
1368 line works on ttyS1 (com2). Now as root, issue the command <em>telinit q</em>
\r
1369 and it should be ready for connection. All that is required is a 3 wire
\r
1370 serial lead (tx, rx and signal ground). Tell you logging program to use
\r
1371 8n1 at 9600 baud and you should see a Linux login prompt. Login as normal
\r
1372 and then telnet from there to the cluster.
\r
1374 <sect>Java Web applet
\r
1377 In the spider tree will be a directory <em>spider-web</em>. This is a
\r
1378 neat little java web applet that can be run from a website. The applet
\r
1379 must run on the same machine as the cluster. The included README file is
\r
1383 I should comment here that the applet is precompiled, that is, ready to go.
\r
1384 It was compiled using JDK1.3.1. If your version is earlier than this then it
\r
1385 may not work. Should that be the case you need to recompile or update your
\r
1386 JDK. To recompile do the following ...
\r
1389 cd /spider/spider-web
\r
1391 /usr/bin/javac spiderclient.java
\r
1395 I have used /usr/bin/javac as an example, your path to javac may be different.
\r
1400 Completely based on a clx web client written in Java by dl6dbh
\r
1401 (ftp://clx.muc.de/pub/clx/clx-java_10130001.tgz)
\r
1403 The webserver has to run on the same machine as your DxSpider software!
\r
1405 It is assumed that you have Java installed. You need JDK1.3.1 at least.
\r
1407 Installation instructions (Performed as root):
\r
1409 Put all the files in the spider-web directory into a newly created directory
\r
1410 under the DocumentRoot of your websever for instance 'client'. In my case
\r
1411 this is: /home/httpd/html/client/ although ymmv. For Suse the correct
\r
1412 path should be /usr/local/httpd/htdocs/client/ for example.
\r
1414 Move spider.cgi to the cgi-bin directory of your webserver, in my case that is
\r
1415 /home/httpd/cgi-bin/ although ymmv. For Suse the correct path should be
\r
1416 /usr/local/httpd/cgi-bin/ for example.
\r
1418 Change the permissions of the files to ensure they are correct, obviously you
\r
1419 will need to use the correct path the the files according to your system:
\r
1421 chmod 755 /home/httpd/html/cgi-bin/spider.cgi
\r
1422 chmod -R 755 /home/httpd/html/client/
\r
1424 By default the spider.cgi script should pick up your hostname (As long as this
\r
1425 is set correctly). If it does not or your hostname differs from the name that
\r
1426 you attach to the public address that you are using, then edit spider.cgi :
\r
1428 # Uncomment and set the hostname manually here if the above fails.
\r
1429 # $HOSTNAME = "gb7mbc.spoo.org" ;
\r
1432 'HOSTNAME' is the hostname of your cluster.
\r
1434 'PORT' is the portnumber that you use to connect to your DxSpider via
\r
1435 telnet (see Listeners.pm)
\r
1437 NOTE: If you can start the console but cannot connect to the cluster from it,
\r
1438 then it is possible that the machine you are on cannot resolve the hostname of
\r
1439 your cluster machine. If this is the case, you need to set your hostname
\r
1440 manually as above.
\r
1442 You also need to set the $NODECALL variable. This prints the name of your
\r
1443 choosing (probably your cluster callsign) on the html page.
\r
1445 You now can connect to Spider-Web via http://yourserver/cgi-bin/spider.cgi
\r
1448 <sect>Web based statistics
\r
1451 From version 1.50, you can use the freeware software MRTG to produce
\r
1452 really nice graphical statistics on your web site. For an example
\r
1453 try <htmlurl url="http://www.gb7mbc.net/mrtg/stats.html" name="http://www.gb7mbc.net/mrtg/stats.html">.
\r
1456 The following should help you get it all working.
\r
1459 First you need to download the latest version of MRTG from <htmlurl url="http://people.ee.ethz.ch/~oetiker/webtools/mrtg/" name="http://people.ee.ethz.ch/~oetiker/webtools/mrtg/">.
\r
1460 You will also need the following files..
\r
1463 libpng-1.0.14.tar.gz
\r
1468 Login to your machine as the root user, put all the downloaded files
\r
1469 in /usr/local/src/ (or wherever you prefer) and untar and compile them.
\r
1470 All the information to compile and install these sources come with them.
\r
1471 After compilation and installation, you will find MRTG in /usr/local/mrtg-2.
\r
1474 Now copy all the files in /usr/local/src/mrtg-2.9.22/images/ to
\r
1475 /spider/html/mrtg/
\r
1478 You now need to make 2 symbolic links like below...
\r
1481 ln -s /usr/local/mrtg-2/bin/mrtg /usr/bin/mrtg
\r
1482 ln -s /usr/local/mrtg-2/lib/mrtg2 /usr/lib/mrtg2
\r
1486 Now login to the cluster with your sysop callsign and run the command
\r
1489 <P>Now you are nearly there! Login as the sysop user and change to the
\r
1490 /spider/html/mrtg/ directory. Now run the command <em>indexmaker</em> as
\r
1494 indexmaker --output stats.html --columns=1 --title "MRTG statistics for GB7DJK" ../../mrtg/mrtg.cfg
\r
1497 Changing the callsign for your own cluster callsign of course!
\r
1500 And finally you need to login as the root user and create one last
\r
1501 symbolic link. Where this points will depend on where your html
\r
1502 documents are kept. For RedHat systems you use...
\r
1505 ln -s /home/sysop/spider/html/mrtg /home/httpd/html/mrtg
\r
1508 and for SuSE systems...
\r
1511 ln -s /home/sysop/spider/html/mrtg /usr/local/httpd/htdocs/mrtg
\r
1514 If you now point your browser to your website as below it should all
\r
1518 http://www.xxx.xxx/mrtg/stats.html
\r
1521 Of course, to get the stats to update, you need to add some information
\r
1522 in the spider crontab file as below...
\r
1525 # Update stats for mrtg on website
\r
1526 00,05,10,15,20,25,30,35,40,45,50,55 * * * * run_cmd('mrtg all')
\r
1529 This will update the site every 5 minutes.
\r
1534 From version 1.49 DXSpider has some additional security features. These
\r
1535 are not by any means meant to be exhaustive, however they do afford some
\r
1536 security against piracy. These two new features can be used independently
\r
1537 of each other or in concert to tighten the security.
\r
1539 <sect1>Registration
\r
1542 The basic principle of registration is simple. If a user is not registered
\r
1543 by the sysop, then they have read-only access to the cluster. The only
\r
1544 thing they can actually send is a talk or a message to the sysop. In
\r
1545 order for them to be able to spot, send announces or talks etc the sysop
\r
1546 must register them with the <em>set/register</em> command, like this ...
\r
1549 set/register g0vgs
\r
1552 The user g0vgs can now fully use the cluster. In order to enable
\r
1553 registration, you can issue the command ...
\r
1556 set/var $main::reqreg = 1
\r
1559 Any users that are not registered will now see the motd_nor file rather
\r
1560 than the motd file as discussed in the Information, files and useful
\r
1564 Entering this line at the prompt will only last for the time the cluster
\r
1565 is running of course and would not be present on a restart. To make the
\r
1566 change permanent, add the above line to /spider/scripts/startup. To
\r
1567 read more on the startup file, see the section on Information, files
\r
1568 and useful programs.
\r
1571 To unregister a user use <em>unset/register</em> and to show the list
\r
1572 of registered users, use the command <em>show/register</em>.
\r
1577 At the moment, passwords only affect users who login to a DXSpider
\r
1578 cluster node via telnet. If a user requires a password, they can
\r
1579 either set it themselves or have the sysop enter it for them by using
\r
1580 the <em>set/password</em> command. Any users who already have passwords,
\r
1581 such as remote sysops, will be asked for their passwords automatically
\r
1582 by the cluster. Using passwords in this way means that the user has a
\r
1583 choice on whether to have a password or not. To force the use of
\r
1584 passwords at login, issue the command ...
\r
1587 set/var $main::passwdreq = 1
\r
1590 at the cluster prompt. This can also be added to the /spider/scripts/startup
\r
1591 file as above to make the change permanent.
\r
1594 Of course, if you do this you will have to assign a password for each of
\r
1595 your users. If you were asking them to register, it is anticipated that
\r
1596 you would ask them to send you a message both to ask to be registered and
\r
1597 to give you the password they wish to use.
\r
1600 Should a user forget their password, it can be reset by the sysop by
\r
1601 first removing the existing password and then setting a new one like so ...
\r
1604 unset/password g0vgs
\r
1605 set/password g0vgs new_password
\r
1610 <sect1>CVS from a Linux platform
\r
1613 CVS stands for "Concurrent Versions System" and the CVS for DXSpider is held
\r
1614 at <htmlurl url="http://www.sourceforge.net" name="Sourceforge">. This means
\r
1615 that it is possible to update your DXSpider installation to the latest
\r
1616 sources by using a few simple commands. A graphical interface to CVS for
\r
1617 Windows is explained in the next section.
\r
1620 Please be aware that if you update your system using CVS, it is possible that
\r
1621 you could be running code that is very beta and not fully tested. There is
\r
1622 a possibility that it could be unstable.
\r
1625 I am of course assuming that you have a machine with both DXSpider and
\r
1626 Internet access running.
\r
1629 BEFORE YOU EVEN CONSIDER STARTING WITH THIS MAKE A BACKUP OF YOUR
\r
1630 ENTIRE SPIDER TREE!!
\r
1633 Assuming you are connected to the Internet, you need to login to the
\r
1634 CVS repository and then update your Spider source. There are several
\r
1635 steps which are listed below ...
\r
1638 First login as the user <em>sysop</em>. Next you need to connect to the CVS
\r
1639 repository. You do this with the command below ...
\r
1642 cvs -d:pserver:anonymous@cvs.DXSpider.sourceforge.net:/cvsroot/dxspider login
\r
1645 You will get a password prompt. Simply hit return here and your machine should
\r
1646 return to a normal linux prompt.
\r
1649 What happens next depends on whether you have an existing installation that
\r
1650 you want to update with the latest and greatest or whether you just want
\r
1651 to see what is there and/or run it on a new machine for testing.
\r
1653 If you are installing Spider from CVS then change directory to /home/sysop
\r
1655 If you are wanting to update Spider then cd to /tmp
\r
1658 The next step will create a brand new 'spider' directory in your current
\r
1662 cvs -z3 -d:pserver:anonymous@cvs.DXSpider.sourceforge.net:/cvsroot/dxspider co spider
\r
1665 This command is all on one line.
\r
1668 Hopefully your screen should show you downloading files. The -z3 simply compresses
\r
1669 the download to improve speed.
\r
1670 When this has finished, you will have exactly the same as if you had untarred a full
\r
1671 tarball PLUS some extra directories and files that CVS needs to do the magic that
\r
1675 Now if you are doing a new installation, that's it. Carry on as if you have
\r
1676 just downloaded and untarred the lastest tarball.
\r
1679 If you want to upgrade your current installation then do this ...
\r
1682 tar cvfz /tmp/s.tgz spider
\r
1684 tar xvfzp /tmp/s.tgz
\r
1687 This is assuming you downloaded to the /tmp directory of course.
\r
1690 NOTE: the 'p' on the end of the 'xvfz' is IMPORTANT! It keeps the permissions
\r
1691 correct. YOU WERE LOGGED IN AS THE USER SYSOP WEREN'T YOU?????
\r
1693 Remember to recompile the C client (cd /spider/src; make)
\r
1696 At this point the files have been upgraded. You can (usually) restart the cluster
\r
1697 in your own time. However, if you attempt to use any new commands or features
\r
1698 expect it to be fatal! At least your cluster will have been restarted then so it
\r
1699 will be too late to worry about it!
\r
1702 Now the magic part! From now on when you want to update, simply connect to the
\r
1703 Internet and then, as the user <em>sysop</em> ...
\r
1710 and your files will be updated. As above, remember to recompile the "C" client
\r
1711 if it has been updated (CVS will tell you) and restart if any of the perl scripts
\r
1712 have been altered or added, again, CVS will tell you.
\r
1715 You will find any changes documented in the /spider/Changes file.
\r
1717 <sect1>CVS from a Windows platform
\r
1720 After the initial setup, an update to your DXSpider software is no more than a couple
\r
1721 of clicks away. This section is intended to explain and illustrate the use of the
\r
1722 WinCVS application to update your DXSpider software. The current stable version of
\r
1723 WinCVS is Ver. 1.2. You can get this software at:
\r
1725 <htmlurl url="http://prdownloads.sourceforge.net/cvsgui/WinCvs120.zip" name="http://prdownloads.sourceforge.net/cvsgui/WinCvs120.zip">
\r
1727 Pick your download mirror and then install WinCVS after the download is complete.
\r
1729 In this next section I have included a series of links to .jpg files to take advantage of the
\r
1730 picture and 1000 words equivalency. The .jpg files are in the C:\spider\html directory. If
\r
1731 someone using a Linux system is reading this section from boredom, the files are in
\r
1732 /home/sysop/spider/html. One aside, a Linux user can also get a copy of gcvs and do your updates
\r
1733 graphically as opposed to from the command line. The following descriptions are almost identical
\r
1734 between WinCvs and gcvs. The following screen shots have duplicate links, depending upon whether
\r
1735 you are viewing this information under the Windows or Linux operating system.
\r
1737 When WinCVS is installed, running, and you are connected to the internet, the initial screen looks like:
\r
1739 <htmlurl url="initial.jpg" name="initial.jpg">
\r
1741 If you want, you can also look at these .jpg files with another viewer that might provide some
\r
1742 better clarity to the image. On the left is the directory tree for your hard disk. Notice that
\r
1743 the spider directory has a gray highlight.
\r
1745 To start configuring WinCVS, click on Admin at the top of the screen and then Preferences. This
\r
1748 <htmlurl url="pref-gen.jpg" name="pref-gen.jpg">
\r
1750 In the top line for CVSROOT, enter:
\r
1752 anonymous@cvs.DXSpider.sourceforge.net:/cvsroot/dxspider login
\r
1757 "passwd" file on the cvs server
\r
1760 for Authentication on the General tab.
\r
1762 Next, move to the right to the Ports tab.
\r
1764 <htmlurl url="pref-ports.jpg" name="pref-ports.jpg">
\r
1766 In here, check the box on the second line down for the "pserver" port. Enter a port number of 2401.
\r
1768 Finally, go to the WinCvs tab all the way to the right.
\r
1770 <htmlurl url="pref-wincvs.jpg" name="pref-wincvs.jpg">
\r
1772 Enter Notepad as the viewer to open files. For the HOME folder, put "C:\spider" and click OK
\r
1773 because the configuration is now complete.
\r
1775 You are now ready to upgrade your copy of DXSpider. Click on the greyed Spider folder
\r
1776 shown in the directory tree on the left of the WinCVS display. Two things should happen. The Spider
\r
1777 folder will be selected and the greyed-out arrow located just below the word Query in the top line will
\r
1778 turn to solid green.
\r
1780 For anyone using gcvs under Linux, the green arrow is located on the extreme left of the display,
\r
1781 under the word File. A gcvs screen looks like:
\r
1783 <htmlurl url="gcvs.jpg" name="gcvs.jpg">
\r
1785 Click on the now green arrow to start the download process. An Update Settings box will be displayed
\r
1786 to which you can simply say OK.
\r
1788 <htmlurl url="update-OK.jpg" name="update-OK.jpg">
\r
1790 For future reference, the Update Settings box is the place where you can enter information to revert
\r
1791 to a prior version of DXSpider. Information on reverting to a Before Date is contained in the WinCVS
\r
1794 After a short period of time, a series of file names will scroll by in the lower pane of the WinCVS
\r
1795 window. Eventually you should see
\r
1797 *****CVS exited normally with code 0*****
\r
1800 appear in the lower pane. You're done. The updated files are in place ready for you to stop and then
\r
1801 restart your DXSpider. After the restart, you're running with the latest version of DXSpider.
\r
1803 <htmlurl url="completed.jpg" name="completed.jpg">
\r
1805 To paraphrase from the CVS section... Now the magic part! From now on when you want to update, simply
\r
1806 connect to the Internet and start WinCVS.
\r
1808 Click on the greyed-out Spider directory in the left screen
\r
1809 Click on the green down arrow
\r
1810 Click OK on the Update Settings dialog box
\r
1811 Restart your Spider software
\r
1818 <bf>accept</bf> Set a filter to accept something
1822 Create a filter to accept something
1824 There are 2 types of filter, accept and reject. See HELP FILTERING for more
1826 <sect1>accept/announce <call> [input] [0-9] <pattern> (8)
1830 <bf>accept/announce <call> [input] [0-9] <pattern></bf> Announce filter sysop version
1834 This version allows a sysop to set a filter for a callsign as well as the
1835 default for nodes and users eg:-
1839 accept/ann input node_default by G,M,2
1840 accept/ann user_default by G,M,2
1843 <sect1>accept/announce [0-9] <pattern> (0)
1847 <bf>accept/announce [0-9] <pattern></bf> Set an 'accept' filter line for announce
1851 Create an 'accept this announce' line for a filter.
1853 An accept filter line means that if the announce matches this filter it is
1854 passed onto the user. See HELP FILTERING for more info. Please read this
1855 to understand how filters work - it will save a lot of grief later on.
1857 You can use any of the following things in this line:-
1860 info <string> eg: iota or qsl
1861 by <prefixes> eg: G,M,2
1862 origin <prefixes>
1863 origin_dxcc <prefixes or numbers> eg: 61,62 (from eg: sh/pre G)
1864 origin_itu <prefixes or numbers> or: G,GM,GW
1865 origin_zone <prefixes or numbers>
1866 origin_state <states> eg: VA,NH,RI,NH
1867 by_dxcc <prefixes or numbers>
1868 by_itu <prefixes or numbers>
1869 by_zone <prefixes or numbers>
1870 by_state <states>
1871 channel <prefixes>
1872 wx 1 filter WX announces
1873 dest <prefixes> eg: 6MUK,WDX (distros)
1880 acc/ann 2 by_zone 14,15,16
1881 (this could be all on one line: acc/ann dest 6MUK or by_zone 14,15,16)
1891 acc/ann by_state va,nh,ri,nh
1894 You can use the tag 'all' to accept everything eg:
1900 but this probably for advanced users...
1901 <sect1>accept/route <call> [0-9] <pattern> (8)
1905 <bf>accept/route <call> [0-9] <pattern></bf> Set an 'accept' filter line for routing
1909 Create an 'accept this routing PC Protocol' line for a filter.
1911 An accept filter line means that if a PC16/17/19/21/24/41/50 matches this filter
1912 it is passed thru that interface. See HELP FILTERING for more info. Please read this
1913 to understand how filters work - it will save a lot of grief later on.
1915 You can use any of the following things in this line:-
1918 call <prefixes> the callsign of the thingy
1919 call_dxcc <prefixes or numbers> eg: 61,62 (from eg: sh/pre G)
1920 call_itu <prefixes or numbers> or: G,GM,GW
1921 call_zone <prefixes or numbers>
1922 call_state <states> eg: VA,NH,RI,NH
1923 origin <prefixes> really the interface it came in on
1924 origin_dxcc <prefixes or numbers> eg: 61,62 (from eg: sh/pre G)
1925 origin_itu <prefixes or numbers> or: G,GM,GW
1926 origin_zone <prefixes or numbers>
1927 origin_state <states> eg: VA,NH,RI,NH
1933 acc/route gb7djk call_dxcc 61,38 (send only UK+EIRE nodes)
1934 acc/route gb7djk call gb7djk (equiv to SET/ISOLATE)
1937 you can now use 'by' as a synonym for 'call' so:
1946 You can use the tag 'all' to accept everything eg:
1952 <sect1>accept/spots <call> [input] [0-9] <pattern> (8)
1956 <bf>accept/spots <call> [input] [0-9] <pattern></bf> Spot filter sysop version
1960 This version allows a sysop to set a filter for a callsign as well as the
1961 default for nodes and users eg:-
1964 accept/spot db0sue-7 1 by_zone 14,15,16
1965 accept/spot node_default all
1966 set/hops node_default 10
1970 accept/spot user_default by G,M,2
1973 <sect1>accept/spots [0-9] <pattern> (0)
1977 <bf>accept/spots [0-9] <pattern></bf> Set an 'accept' filter line for spots
1981 Create an 'accept this spot' line for a filter.
1983 An accept filter line means that if the spot matches this filter it is
1984 passed onto the user. See HELP FILTERING for more info. Please read this
1985 to understand how filters work - it will save a lot of grief later on.
1987 You can use any of the following things in this line:-
1990 freq <range> eg: 0/30000 or hf or hf/cw or 6m,4m,2m
1991 on <range> same as 'freq'
1992 call <prefixes> eg: G,PA,HB9
1993 info <string> eg: iota or qsl
1995 call_dxcc <prefixes or numbers> eg: 61,62 (from eg: sh/pre G)
1996 call_itu <prefixes or numbers> or: G,GM,GW
1997 call_zone <prefixes or numbers>
1998 call_state <states> eg: VA,NH,RI,ME
1999 by_dxcc <prefixes or numbers>
2000 by_itu <prefixes or numbers>
2001 by_zone <prefixes or numbers>
2002 by_state <states> eg: VA,NH,RI,ME
2003 origin <prefixes>
2004 channel <prefixes>
2007 'call' means the callsign that has spotted 'by' whoever.
2009 For frequencies, you can use any of the band names defined in
2010 SHOW/BANDS and you can use a subband name like: cw, rtty, data, ssb -
2011 thus: hf/ssb. You can also just have a simple range like: 0/30000 -
2012 this is more efficient than saying simply: freq HF (but don't get
2013 too hung up about that)
2019 acc/spot 2 on vhf and (by_zone 14,15,16 or call_zone 14,15,16)
2022 You can use the tag 'all' to accept everything, eg:
2031 acc/spots by_state VA,NH,RI,MA,ME
2034 but this probably for advanced users...
2035 <sect1>accept/wcy <call> [input] [0-9] <pattern> (8)
2039 <bf>accept/wcy <call> [input] [0-9] <pattern></bf> WCY filter sysop version
2043 This version allows a sysop to set a filter for a callsign as well as the
2044 default for nodes and users eg:-
2047 accept/wcy node_default all
2048 set/hops node_default 10
2051 <sect1>accept/wcy [0-9] <pattern> (0)
2055 <bf>accept/wcy [0-9] <pattern></bf> set an 'accept' WCY filter
2059 It is unlikely that you will want to do this, but if you do then you can
2060 filter on the following fields:-
2063 by <prefixes> eg: G,M,2
2064 origin <prefixes>
2065 origin_dxcc <prefixes or numbers> eg: 61,62 (from eg: sh/pre G)
2066 origin_itu <prefixes or numbers> or: G,GM,GW
2067 origin_zone <prefixes or numbers>
2068 by_dxcc <prefixes or numbers>
2069 by_itu <prefixes or numbers>
2070 by_zone <prefixes or numbers>
2071 channel <prefixes>
2074 There are no examples because WCY Broadcasts only come from one place and
2075 you either want them or not (see UNSET/WCY if you don't want them).
2077 This command is really provided for future use.
2079 See HELP FILTER for information.
2080 <sect1>accept/wwv <call> [input] [0-9] <pattern> (8)
2084 <bf>accept/wwv <call> [input] [0-9] <pattern></bf> WWV filter sysop version
2088 This version allows a sysop to set a filter for a callsign as well as the
2089 default for nodes and users eg:-
2092 accept/wwv db0sue-7 1 by_zone 4
2093 accept/wwv node_default all
2094 set/hops node_default 10
2098 accept/wwv user_default by W,K
2101 <sect1>accept/wwv [0-9] <pattern> (0)
2105 <bf>accept/wwv [0-9] <pattern></bf> set an 'accept' WWV filter
2109 It is unlikely that you will want to do this, but if you do then you can
2110 filter on the following fields:-
2113 by <prefixes> eg: G,M,2
2114 origin <prefixes>
2115 origin_dxcc <prefixes or numbers> eg: 61,62 (from eg: sh/pre G)
2116 origin_itu <prefixes or numbers> or: G,GM,GW
2117 origin_zone <prefixes or numbers>
2118 by_dxcc <prefixes or numbers>
2119 by_itu <prefixes or numbers>
2120 by_zone <prefixes or numbers>
2121 channel <prefixes>
2127 accept/wwv by_zone 4
2130 is probably the only useful thing to do (which will only show WWV broadcasts
2131 by stations in the US).
2133 See HELP FILTER for information.
2134 <sect1>announce <text> (0)
2138 <bf>announce <text></bf> Send an announcement to LOCAL users only
2142 <text> is the text of the announcement you wish to broadcast
2143 <sect1>announce full <text> (0)
2147 <bf>announce full <text></bf> Send an announcement cluster wide
2151 This will send your announcement cluster wide
2152 <sect1>announce sysop <text> (5)
2156 <bf>announce sysop <text></bf> Send an announcement to Sysops only
2160 <sect1>apropos <string> (0)
2164 <bf>apropos <string></bf> Search help database for <string>
2168 Search the help database for <string> (it isn't case sensitive), and print
2169 the names of all the commands that may be relevant.
2170 <sect1>blank [<string>] [<nn>] (0)
2174 <bf>blank [<string>] [<nn>]</bf> Print nn (default 1) blank lines (or strings)
2178 In its basic form this command prints one or more blank lines. However if
2179 you pass it a string it will replicate the string for the width of the
2180 screen (default 80) and then print that one or more times, so:
2186 prints two blank lines
2192 prints a row of - characters once.
2198 prints 'abcabcabcabcabcabc....'
2200 This is really only of any use in a script file and you can print a maximum
2206 <bf>bye</bf> Exit from the cluster
2210 This will disconnect you from the cluster
2211 <sect1>catchup <node call> all|[<msgno> ...] (5)
2215 <bf>catchup <node call> all|[<msgno> ...]</bf> Mark a message as sent
2219 <sect1>chat <group> <text> (0)
2223 <bf>chat <group> <text></bf> Chat or Conference to a group
2227 It is now possible to JOIN a group and have network wide conferencing to that
2228 group. DXSpider does not (and probably will not) implement the AK1A
2229 conference mode as this seems very limiting, is hardly used and doesn't seem
2230 to work too well anyway.
2232 This system uses the existing ANN system and is compatible with both other
2233 DXSpider nodes and AK1A clusters (they use ANN/<group>).
2235 You can be a member of as many "groups" as you want. To join a group type:-
2238 JOIN FOC (where FOC is the group name)
2241 To leave a group type:-
2247 You can see which groups you are in by typing:-
2253 and you can see whether your mate is in the group, if he connects to the
2254 same node as you, by typing:-
2260 To send a message to a group type:-
2263 CHAT FOC hello everyone
2269 CH #9000 hello I am back
2272 See also JOIN, LEAVE, SHOW/CHAT
2273 <sect1>clear/announce <callsign> [input] [0-9|all] (8)
2277 <bf>clear/announce <callsign> [input] [0-9|all]</bf> Clear a announce filter line
2281 A sysop can clear an input or normal output filter for a user or the
2282 node_default or user_default.
2283 <sect1>clear/announce [1|all] (0)
2287 <bf>clear/announce [1|all]</bf> Clear a announce filter line
2291 This command allows you to clear (remove) a line in a annouce filter or to
2292 remove the whole filter.
2294 see CLEAR/SPOTS for a more detailed explanation.
2295 <sect1>clear/route <callsign> [input] [0-9|all] (8)
2299 <bf>clear/route <callsign> [input] [0-9|all]</bf> Clear a route filter line
2303 A sysop can clear an input or normal output filter for a user or the
2304 node_default or user_default.
2305 <sect1>clear/route [1|all] (0)
2309 <bf>clear/route [1|all]</bf> Clear a route filter line
2313 This command allows you to clear (remove) a line in a route filter or to
2314 remove the whole filter.
2316 see CLEAR/SPOTS for a more detailed explanation.
2317 <sect1>clear/spots <callsign> [input] [0-9|all] (8)
2321 <bf>clear/spots <callsign> [input] [0-9|all]</bf> Clear a spot filter line
2325 A sysop can clear an input or normal output filter for a user or the
2326 node_default or user_default.
2327 <sect1>clear/spots [0-9|all] (0)
2331 <bf>clear/spots [0-9|all]</bf> Clear a spot filter line
2335 This command allows you to clear (remove) a line in a spot filter or to
2336 remove the whole filter.
2338 If you have a filter:-
2342 acc/spot 2 on vhf and (by_zone 14,15,16 or call_zone 14,15,16)
2351 you will be left with:-
2354 acc/spot 2 on vhf and (by_zone 14,15,16 or call_zone 14,15,16)
2363 the filter will be completely removed.
2364 <sect1>clear/wcy <callsign> [input] [0-9|all] (8)
2368 <bf>clear/wcy <callsign> [input] [0-9|all]</bf> Clear a WCY filter line
2372 A sysop can clear an input or normal output filter for a user or the
2373 node_default or user_default.
2374 <sect1>clear/wcy [1|all] (0)
2378 <bf>clear/wcy [1|all]</bf> Clear a WCY filter line
2382 This command allows you to clear (remove) a line in a WCY filter or to
2383 remove the whole filter.
2385 see CLEAR/SPOTS for a more detailed explanation.
2386 <sect1>clear/wwv <callsign> [input] [0-9|all] (8)
2390 <bf>clear/wwv <callsign> [input] [0-9|all]</bf> Clear a WWV filter line
2394 A sysop can clear an input or normal output filter for a user or the
2395 node_default or user_default.
2396 <sect1>clear/wwv [1|all] (0)
2400 <bf>clear/wwv [1|all]</bf> Clear a WWV filter line
2404 This command allows you to clear (remove) a line in a WWV filter or to
2405 remove the whole filter.
2407 see CLEAR/SPOTS for a more detailed explanation.
2408 <sect1>connect <callsign> (5)
2412 <bf>connect <callsign></bf> Start a connection to another DX Cluster
2416 Start a connection process that will culminate in a new connection to the
2417 DX cluster <callsign>. This process creates a new 'client' process which will
2418 use the script in /spider/connect/<callsign> to effect the 'chat' exchange
2419 necessary to traverse the network(s) to logon to the cluster <callsign>.
2424 <bf>dbavail</bf> Show a list of all the Databases in the system
2428 Title says it all really, this command lists all the databases defined
2429 in the system. It is also aliased to SHOW/COMMAND.
2430 <sect1>dbcreate <name> (9)
2434 <bf>dbcreate <name></bf> Create a database entry
2438 <sect1>dbcreate <name> chain <name> [<name>..] (9)
2442 <bf>dbcreate <name> chain <name> [<name>..]</bf> Create a chained database entry
2446 <sect1>dbcreate <name> cmd <dxspider command> (9)
2450 <bf>dbcreate <name> cmd <dxspider command></bf> make a local command available as a DB
2454 DBCREATE allows you to define a database in the system. It doesn't actually
2455 create anything, just defines it.
2457 The databases that are created are simple DB_File hash databases, they are
2458 therefore already 'indexed'.
2460 You can define a local database with the first form of the command eg:
2466 You can also chain databases with the addition of the 'chain' keyword.
2467 This will search each database one after the other. A typical example
2471 DBCREATE sdx_qsl chain sql_ad
2474 No checking is done to see if the any of the chained databases exist, in
2475 fact it is usually better to do the above staement first then do each of
2476 the chained databases.
2478 Databases can exist offsite. To define a database that lives on another
2482 DBCREATE buckmaster remote gb7dxc
2485 Remote databases cannot be chained; however, the last database in a
2486 a chain can be a remote database eg:
2489 DBCREATE qsl chain gb7dxc
2492 To see what databases have been defined do:
2495 DBAVAIL (or it will have been aliased to SHOW/COMMAND)
2498 It would be normal for you to add an entry into your local Aliases file
2499 to allow people to use the 'SHOW/<dbname>' style syntax. So you would
2500 need to add a line like:-
2506 '^sh\w*/buc', 'dbshow buckmaster', 'dbshow',
2518 to work as they may be used to.
2520 You can also make local commands available as 'pseudo' databases. You
2521 can therefore make spider special commands available as a database. I
2522 imagine that this will be primarily useful for remote access from
2523 legacy nodes. For example:-
2526 DBCREATE dxqsl cmd show/dxqsl
2529 You also use one of these databases in a chain. This may be useful
2532 See DBIMPORT for the importing of existing AK1A format data to databases.
2533 See DBSHOW for generic database enquiry
2535 <sect1>dbcreate <name> remote <node> (9)
2539 <bf>dbcreate <name> remote <node></bf> Create a remote database entry
2543 <sect1>dbimport <dbname> <filename> (9)
2547 <bf>dbimport <dbname> <filename></bf> Import AK1A data into a database
2551 If you want to import or update data in bulk to a database you can use
2552 this command. It will either create or update entries into an existing
2553 database. For example:-
2556 DBIMPORT oblast /tmp/OBLAST.FUL
2559 will import the standard OBLAST database that comes with AK1A into the
2560 oblast database held locally.
2561 <sect1>dbremove <dbname> (9)
2565 <bf>dbremove <dbname></bf> Delete a database
2569 DBREMOVE will completely remove a database entry and also delete any data
2570 file that is associated with it.
2572 There is no warning, no comeback, no safety net.
2580 will remove the oblast database from the system and it will also remove
2581 the associated datafile.
2585 There is no warning, no comeback, no safety net.
2587 You have been warned.
2588 <sect1>dbshow <dbname> <key> (0)
2592 <bf>dbshow <dbname> <key></bf> Display an entry, if it exists, in a database
2596 This is the generic user interface to the database to the database system.
2597 It is expected that the sysop will add an entry to the local Aliases file
2598 so that users can use the more familiar AK1A style of enquiry such as:
2604 but if he hasn't and the database really does exist (use DBAVAIL or
2605 SHOW/COMMAND to find out) you can do the same thing with:
2615 <bf>debug</bf> Set the cluster program into debug mode
2619 Executing this command will only have an effect if you are running the cluster
2626 It will interrupt the cluster just after the debug command has finished.
2627 <sect1>delete/usdb <callsign> ... (9)
2631 <bf>delete/usdb <callsign> ...</bf> Delete this user from the US State Database
2635 This command will completely remove a one or more callsigns
2636 from the US States database.
2638 There is NO SECOND CHANCE.
2640 It goes without saying that you should use this command CAREFULLY!
2642 Note that these callsign may be re-instated by any weekly updates from
2644 <sect1>delete/user <callsign> ... (9)
2648 <bf>delete/user <callsign> ...</bf> Delete this user from the User Database
2652 This command will completely remove a one or more users from the database.
2654 There is NO SECOND CHANCE.
2656 It goes without saying that you should use this command CAREFULLY!
2657 <sect1>demonstrate <call> <command> (9)
2661 <bf>demonstrate <call> <command></bf> Demonstrate a command to another user
2665 This command is provided so that sysops can demonstrate commands to
2666 other users. It runs a command as though that user had typed it in and
2667 then sends the output to that user, together with the command that
2671 DEMO g7brn sh/dx iota oc209
2675 Note that this command is similar to SPOOF and will have the same side
2676 effects. Commands are run at the privilege of the user which is being
2678 <sect1>directory (0)
2682 <bf>directory</bf> List messages
2686 <sect1>directory <from>-<to> (0)
2690 <bf>directory <from>-<to></bf> List messages <from> message <to> message
2694 List the messages in the messages directory.
2696 If there is a 'p' one space after the message number then it is a
2697 personal message. If there is a '-' between the message number and the
2698 'p' then this indicates that the message has been read.
2700 You can use shell escape characters such as '*' and '?' in the <call>
2703 You can combine some of the various directory commands together eg:-
2710 DIR SUBJECT IOTA 200-250
2713 You can abbreviate all the commands to one letter and use ak1a syntax:-
2720 <sect1>directory <nn> (0)
2724 <bf>directory <nn></bf> List last <nn> messages
2728 <sect1>directory all (0)
2732 <bf>directory all</bf> List all messages
2736 <sect1>directory from <call> (0)
2740 <bf>directory from <call></bf> List all messages from <call>
2744 <sect1>directory new (0)
2748 <bf>directory new</bf> List all new messages
2752 <sect1>directory own (0)
2756 <bf>directory own</bf> List your own messages
2760 <sect1>directory subject <string> (0)
2764 <bf>directory subject <string></bf> List all messages with <string> in subject
2768 <sect1>directory to <call> (0)
2772 <bf>directory to <call></bf> List all messages to <call>
2776 <sect1>directory- (5)
2784 Sysops can see all users' messages.
2785 <sect1>disconnect <call> [<call> ...] (8)
2789 <bf>disconnect <call> [<call> ...]</bf> Disconnect a user or cluster
2793 Disconnect any <call> connected locally
2794 <sect1>dx [by <call>] <freq> <call> <remarks> (0)
2798 <bf>dx [by <call>] <freq> <call> <remarks></bf> Send a DX spot
2802 This is how you send a DX Spot to other users. You can, in fact, now
2803 enter the <freq> and the <call> either way round.
2811 will all give the same result. You can add some remarks to the end
2812 of the command and they will be added to the spot.
2815 DX FR0G 144600 this is a test
2818 You can credit someone else by saying:-
2821 DX by G1TLH FR0G 144.600 he isn't on the cluster
2824 The <freq> is compared against the available bands set up in the
2825 cluster. See SHOW/BANDS for more information.
2826 <sect1>echo <line> (0)
2830 <bf>echo <line></bf> Echo the line to the output
2834 This command is useful in scripts and so forth for printing the
2835 line that you give to the command to the output. You can use this
2836 in user_default scripts and the SAVE command for titling and so forth
2838 The script will interpret certain standard "escape" sequences as follows:-
2841 \t - becomes a TAB character (0x09 in ascii)
2842 \a - becomes a BEEP character (0x07 in ascii)
2843 \n - prints a new line
2846 So the following example:-
2849 echo GB7DJK is a dxcluster
2855 GB7DJK is a dxcluster
2858 on the output. You don't need a \n on the end of the line you want to send.
2860 A more complex example:-
2863 echo GB7DJK\n\tg1tlh\tDirk\n\tg3xvf\tRichard
2876 <sect1>export <msgno> <filename> (9)
2880 <bf>export <msgno> <filename></bf> Export a message to a file
2884 Export a message to a file. This command can only be executed on a local
2885 console with a fully privileged user. The file produced will be in a form
2886 ready to be imported back into the cluster by placing it in the import
2887 directory (/spider/msg/import).
2889 This command cannot overwrite an existing file. This is to provide some
2890 measure of security. Any files written will owned by the same user as the
2891 main cluster, otherwise you can put the new files anywhere the cluster can
2892 access. For example:-
2898 <sect1>export_users [<filename>] (9)
2902 <bf>export_users [<filename>]</bf> Export the users database to ascii
2906 Export the users database to a file in ascii format. If no filename
2907 is given then it will export the file to /spider/data/user_asc.
2909 If the file already exists it will be renamed to <filename>.o. In fact
2910 up to 5 generations of the file can be kept each one with an extra 'o' on the
2913 BE WARNED: this will write to any file you have write access to. No check is
2914 made on the filename (if any) that you specify.
2915 <sect1>filtering... (0)
2919 <bf>filtering...</bf> Filtering things in DXSpider
2923 There are a number of things you can filter in the DXSpider system. They
2924 all use the same general mechanism.
2926 In general terms you can create a 'reject' or an 'accept' filter which
2927 can have up to 10 lines in it. You do this using, for example:-
2934 where ..... are the specific commands for that type of filter. There
2935 are filters for spots, wwv, announce, wcy and (for sysops)
2936 connects. See each different accept or reject command reference for
2939 There is also a command to clear out one or more lines in a filter and
2940 one to show you what you have set. They are:-
2953 There is clear/xxxx command for each type of filter.
2955 For now we are going to use spots for the examples, but you can apply
2956 the principles to all types of filter.
2958 There are two main types of filter 'accept' or 'reject'; which you use
2959 depends entirely on how you look at the world and what is least
2960 writing to achieve what you want. Each filter has 10 lines (of any
2961 length) which are tried in order. If a line matches then the action
2962 you have specified is taken (ie reject means ignore it and accept
2965 The important thing to remember is that if you specify a 'reject'
2966 filter (all the lines in it say 'reject/spots' (for instance)) then if
2967 a spot comes in that doesn't match any of the lines then you will get
2968 it BUT if you specify an 'accept' filter then any spots that don't
2969 match are dumped. For example if I have a one line accept filter:-
2972 accept/spots on vhf and (by_zone 14,15,16 or call_zone 14,15,16)
2975 then automatically you will ONLY get VHF spots from or to CQ zones 14
2976 15 and 16. If you set a reject filter like:
2979 reject/spots on hf/cw
2982 Then you will get everything EXCEPT HF CW spots, If you am interested in IOTA
2983 and will work it even on CW then you could say:-
2986 reject/spots on hf/cw and not info iota
2989 But in that case you might only be interested in iota and say:-
2992 accept/spots not on hf/cw or info iota
2995 which is exactly the same. You should choose one or the other until
2996 you are confortable with the way it works. Yes, you can mix them
2997 (actually you can have an accept AND a reject on the same line) but
2998 don't try this at home until you can analyse the results that you get
2999 without ringing up the sysop for help.
3001 Another useful addition now is filtering by US state
3004 accept/spots by_state VA,NH,RI,ME
3007 You can arrange your filter lines into logical units, either for your
3008 own understanding or simply convenience. I have one set frequently:-
3011 reject/spots 1 on hf/cw
3012 reject/spots 2 on 50000/1400000 not (by_zone 14,15,16 or call_zone 14,15,16)
3015 What this does is to ignore all HF CW spots (being a class B I can't
3016 read any CW and couldn't possibly be interested in HF :-) and also
3017 rejects any spots on VHF which don't either originate or spot someone
3020 This is an exmaple where you would use the line number (1 and 2 in
3021 this case), if you leave the digit out, the system assumes '1'. Digits
3022 '0'-'9' are available.
3024 You can leave the word 'and' out if you want, it is implied. You can
3025 use any number of brackets to make the 'expression' as you want
3026 it. There are things called precedence rules working here which mean
3027 that you will NEED brackets in a situation like line 2 because,
3028 without it, will assume:-
3031 (on 50000/1400000 and by_zone 14,15,16) or call_zone 14,15,16
3034 annoying, but that is the way it is. If you use OR - use
3035 brackets. Whilst we are here CASE is not important. 'And BY_Zone' is
3038 If you want to alter your filter you can just redefine one or more
3039 lines of it or clear out one line. For example:-
3042 reject/spots 1 on hf/ssb
3051 To remove the filter in its entirty:-
3057 There are similar CLEAR commands for the other filters:-
3067 Once you are happy with the results you get, you may like to experiment.
3069 my example that filters hf/cw spots and accepts vhf/uhf spots from EU
3070 can be written with a mixed filter, eg:
3075 acc/spot 2 on 50000/1400000 and (by_zone 14,15,16 or call_zone 14,15,16)
3078 each filter slot actually has a 'reject' slot and an 'accept'
3079 slot. The reject slot is executed BEFORE the accept slot.
3081 It was mentioned earlier that after a reject test that doesn't match,
3082 the default for following tests is 'accept', the reverse is true for
3083 'accept'. In the example what happens is that the reject is executed
3084 first, any non hf/cw spot is passed to the accept line, which lets
3085 thru everything else on HF.
3087 The next filter line lets through just VHF/UHF spots from EU.
3088 <sect1>forward/latlong <node_call> (8)
3092 <bf>forward/latlong <node_call></bf> Send latitude and longitude information to another cluster
3096 This command sends all the latitude and longitude information that your
3097 cluster is holding against callsigns. One advantage of recieving this
3098 information is that more locator information is held by you. This
3099 means that more locators are given on the DX line assuming you have
3100 SET/DXGRID enabled. This could be a LOT of information though, so
3101 it is not recommended on slow links.
3102 <sect1>forward/opernam <call> (1)
3106 <bf>forward/opernam <call></bf> Send out information on this <call> to all clusters
3110 This command sends out any information held in the user file which can
3111 be broadcast in PC41 protocol packets. This information is Name, QTH, Location
3112 and Homenode. PC41s are only sent for the information that is available.
3118 <bf>help</bf> The HELP Command
3122 HELP is available for a number of commands. The syntax is:-
3128 Where <cmd> is the name of the command you want help on.
3130 All commands can be abbreviated, so SHOW/DX can be abbreviated
3131 to SH/DX, ANNOUNCE can be shortened to AN and so on.
3133 Look at the APROPOS <string> command which will search the help database
3134 for the <string> you specify and give you a list of likely commands
3135 to look at with HELP.
3136 <sect1>init <node> (5)
3140 <bf>init <node></bf> Re-initialise a link to an AK1A compatible node
3144 This command attempts to re-initialise a link to a (usually) AK1A node
3145 that has got confused, usually by a protocol loop of some kind. It may
3146 work - but you usually will be better off simply disconnecting it (or
3147 better, if it is a real AK1A node, doing an RCMD <node> DISC/F <your
3150 Best of luck - you will need it.
3152 <sect1>join <group> (0)
3156 <bf>join <group></bf> Join a chat or conference group
3160 JOIN allows you to join a network wide conference group. To join a
3161 group (called FOC in this case) type:-
3167 See also CHAT, LEAVE, SHOW/CHAT
3176 As a sysop you can kill any message on the system.
3177 <sect1>kill <from msgno>-<to msgno> (0)
3181 <bf>kill <from msgno>-<to msgno></bf> Delete a range of messages
3185 <sect1>kill <from>-<to> (5)
3189 <bf>kill <from>-<to></bf> Remove a range of messages from the system
3193 <sect1>kill <msgno> [<msgno..] (0)
3197 <bf>kill <msgno> [<msgno..]</bf> Delete a message from the local system
3201 <sect1>kill <msgno> [<msgno> ...] (0)
3205 <bf>kill <msgno> [<msgno> ...]</bf> Remove or erase a message from the system
3209 You can get rid of any message to or originating from your callsign using
3210 this command. You can remove more than one message at a time.
3211 <sect1>kill expunge <msgno> [<msgno..] (6)
3215 <bf>kill expunge <msgno> [<msgno..]</bf> Expunge a message
3219 Deleting a message using the normal KILL commands only marks that message
3220 for deletion. The actual deletion only happens later (usually two days later).
3222 The KILL EXPUNGE command causes the message to be truly deleted more or less
3225 It otherwise is used in the same way as the KILL command.
3226 <sect1>kill from <call> (5)
3230 <bf>kill from <call></bf> Remove all messages from a callsign
3234 <sect1>kill full <msgno> [<msgno..] (5)
3238 <bf>kill full <msgno> [<msgno..]</bf> Delete a message from the whole cluster
3242 Delete a message from the local system. You will only be able to
3243 delete messages that you have originated or been sent (unless you are
3250 Will delete all the messages that you own between msgnos 1234 and 1255.
3256 will delete all the messages from g1tlh (if you are g1tlh). Similarly:
3262 will delete all messages to g1tlh.
3268 will delete a message (usually a 'bulletin') from the whole cluster system.
3270 This uses the subject field, so any messages that have exactly the
3271 same subject will be deleted. Beware!
3272 <sect1>kill full <msgno> [<msgno] (5)
3276 <bf>kill full <msgno> [<msgno]</bf> Remove a message from the entire cluster
3280 Remove this message from the entire cluster system as well as your node.
3281 <sect1>kill to <call> (5)
3285 <bf>kill to <call></bf> Remove all messages to a callsign
3289 <sect1>kill from <regex> (0)
3293 <bf>kill from <regex></bf> Delete messages FROM a callsign or pattern
3297 <sect1>kill to <regex> (0)
3301 <bf>kill to <regex></bf> Delete messages TO a callsign or pattern
3305 <sect1>leave <group> (0)
3309 <bf>leave <group></bf> Leave a chat or conference group
3313 LEAVE allows you to leave a network wide conference group. To leave a
3314 group (called FOC in this case) type:-
3320 See also CHAT, JOIN, SHOW/CHAT
3325 <bf>links</bf> Show which nodes is physically connected
3329 This is a quick listing that shows which links are connected and
3330 some information about them. See WHO for a list of all connections.
3331 <sect1>load/aliases (9)
3335 <bf>load/aliases</bf> Reload the command alias table
3339 Reload the /spider/cmd/Aliases file after you have editted it. You
3340 will need to do this if you change this file whilst the cluster is
3341 running in order for the changes to take effect.
3342 <sect1>load/badmsg (9)
3346 <bf>load/badmsg</bf> Reload the bad msg table
3350 Reload the /spider/msg/badmsg.pl file if you have changed it manually whilst
3351 the cluster is running. This table contains a number of perl regular
3352 expressions which are searched for in the fields targetted of each message.
3353 If any of them match then that message is immediately deleted on receipt.
3354 <sect1>load/badwords (9)
3358 <bf>load/badwords</bf> Reload the bad words table
3362 Reload the /spider/data/badwords file if you have changed it manually whilst
3363 the cluster is running. This file contains a list of words which, if found
3364 on certain text portions of PC protocol, will cause those protocol frames
3365 to be rejected. It will all put out a message if any of these words are
3366 used on the announce, dx and talk commands. The words can be one or
3367 more on a line, lines starting with '#' are ignored.
3368 <sect1>load/bands (9)
3372 <bf>load/bands</bf> Reload the band limits table
3376 Reload the /spider/data/bands.pl file if you have changed it manually whilst
3377 the cluster is running.
3378 <sect1>load/cmd_cache (9)
3382 <bf>load/cmd_cache</bf> Reload the automatic command cache
3386 Normally, if you change a command file in the cmd or local_cmd tree it
3387 will automatially be picked up by the cluster program. Sometimes it
3388 can get confused if you are doing a lot of moving commands about or
3389 delete a command in the local_cmd tree and want to use the normal one
3390 again. Execute this command to reset everything back to the state it
3391 was just after a cluster restart.
3392 <sect1>load/forward (9)
3396 <bf>load/forward</bf> Reload the msg forwarding routing table
3400 Reload the /spider/msg/forward.pl file if you have changed it
3401 manually whilst the cluster is running.
3402 <sect1>load/keps (5)
3406 <bf>load/keps</bf> Load new keps data
3410 <sect1>load/keps [nn] (5)
3414 <bf>load/keps [nn]</bf> Load new keps data from message
3418 If there is no message number then reload the current Keps data from
3419 the Keps.pm data file. You create this file by running
3422 /spider/perl/convkeps.pl <filename>
3425 on a file containing NASA 2 line keps as a message issued by AMSAT.
3427 If there is a message number, then it will take the message, run
3428 convkeps.pl on it and then load the data, all in one step.
3430 These messages are sent to ALL by GB7DJK (and others) from time to time.
3431 <sect1>load/messages (9)
3435 <bf>load/messages</bf> Reload the system messages file
3439 If you change the /spider/perl/Messages file (usually whilst
3440 fiddling/writing new commands) you can have them take effect during a
3441 cluster session by executing this command. You need to do this if get
3444 unknown message 'xxxx' in lang 'en'
3445 <sect1>load/prefixes (9)
3449 <bf>load/prefixes</bf> Reload the prefix table
3453 Reload the /spider/data/prefix_data.pl file if you have changed it
3454 manually whilst the cluster is running.
3455 <sect1>merge <node> [<no spots>/<no wwv>] (5)
3459 <bf>merge <node> [<no spots>/<no wwv>]</bf> Ask for the latest spots and WWV
3463 MERGE allows you to bring your spot and wwv database up to date. By default
3464 it will request the last 10 spots and 5 WWVs from the node you select. The
3465 node must be connected locally.
3467 You can request any number of spots or wwv and although they will be appended
3468 to your databases they will not duplicate any that have recently been added
3469 (the last 2 days for spots and last month for WWV data).
3470 <sect1>msg <cmd> <msgno> [data ... ] (9)
3474 <bf>msg <cmd> <msgno> [data ... ]</bf> Alter various message parameters
3478 Alter message parameters like To, From, Subject, whether private or bulletin
3479 or return receipt (RR) is required or whether to keep this message from timing
3483 MSG TO <msgno> <call> - change TO callsign to <call>
3484 MSG FRom <msgno> <call> - change FROM callsign to <call>
3485 MSG PRrivate <msgno> - set private flag
3486 MSG NOPRrivate <msgno> - unset private flag
3487 MSG RR <msgno> - set RR flag
3488 MSG NORR <msgno> - unset RR flag
3489 MSG KEep <msgno> - set the keep flag (message won't be deleted ever)
3490 MSG NOKEep <msgno> - unset the keep flag
3491 MSG SUbject <msgno> <new> - change the subject to <new>
3492 MSG WAittime <msgno> - remove any waitting time for this message
3493 MSG NOREad <msgno> - mark message as unread
3494 MSG REad <msgno> - mark message as read
3495 MSG QUeue - queue any outstanding bulletins
3496 MSG QUeue 1 - queue any outstanding private messages
3499 You can look at the status of a message by using:-
3502 STAT/MSG <msgno>
3505 This will display more information on the message than DIR does.
3507 <sect1>pc <call> <text> (8)
3511 <bf>pc <call> <text></bf> Send arbitrary text to a connected callsign
3515 Send some arbitrary text to a locally connected callsign. No
3516 processing is done on the text. This command allows you to send PC
3517 Protocol to unstick things if problems arise (messages get stuck
3521 pc gb7djk PC33^GB7TLH^GB7DJK^400^
3525 pc G1TLH Try doing that properly!!!
3528 Send any text you like to the callsign requested. This is used mainly to send
3529 PC protocol to connected nodes either for testing or to unstick things.
3531 You can also use in the same way as a talk command to a connected user but
3532 without any processing, added of "from <blah> to <blah" or whatever.
3534 <sect1>ping <node call> (1)
3538 <bf>ping <node call></bf> Check the link quality between nodes
3542 This command allows you to send a frame to another cluster node on
3543 the network and get a return frame. The time it takes to do this
3544 is a good indication of the quality of the link. The actual time
3545 it takes is output to the console in seconds.
3546 Any visible cluster node can be PINGed.
3547 <sect1>rcmd <node call> <cmd> (1)
3551 <bf>rcmd <node call> <cmd></bf> Send a command to another DX Cluster
3555 This command allows you to send nearly any command to another DX Cluster
3556 node that is connected to the system.
3558 Whether you get any output is dependant on a) whether the other system knows
3559 that the node callsign of this cluster is in fact a node b) whether the
3560 other system is allowing RCMDs from this node and c) whether you have
3561 permission to send this command at all.
3566 <bf>read</bf> Read the next unread personal message addressed to you
3570 <sect1>read <msgno> (0)
3574 <bf>read <msgno></bf> Read the specified message
3578 You can read any messages that are sent as 'non-personal' and also any
3579 message either sent by or sent to your callsign.
3588 As a sysop you may read any message on the system
3593 <bf>reject</bf> Set a filter to reject something
3597 Create a filter to reject something
3599 There are 2 types of filter, accept and reject. See HELP FILTERING for more
3601 <sect1>reject/announce <call> [input] [0-9] <pattern> (8)
3605 <bf>reject/announce <call> [input] [0-9] <pattern></bf> Announce filter sysop version
3609 This version allows a sysop to set a filter for a callsign as well as the
3610 default for nodes and users eg:-
3614 reject/ann input node_default by G,M,2
3615 reject/ann user_default by G,M,2
3618 <sect1>reject/announce [0-9] <pattern> (0)
3622 <bf>reject/announce [0-9] <pattern></bf> Set a 'reject' filter line for announce
3626 Create an 'reject this announce' line for a filter.
3628 A reject filter line means that if the announce matches this filter it is
3629 passed onto the user. See HELP FILTERING for more info. Please read this
3630 to understand how filters work - it will save a lot of grief later on.
3632 You can use any of the following things in this line:-
3635 info <string> eg: iota or qsl
3636 by <prefixes> eg: G,M,2
3637 origin <prefixes>
3638 origin_dxcc <prefixes or numbers> eg: 61,62 (from eg: sh/pre G)
3639 origin_itu <prefixes or numbers> or: G,GM,GW
3640 origin_zone <prefixes or numbers>
3641 origin_state <states> eg: VA,NH,RI,ME
3642 by_dxcc <prefixes or numbers>
3643 by_itu <prefixes or numbers>
3644 by_zone <prefixes or numbers>
3645 by_state <states> eg: VA,NH,RI,ME
3646 channel <prefixes>
3647 wx 1 filter WX announces
3648 dest <prefixes> eg: 6MUK,WDX (distros)
3654 rej/ann by_zone 14,15,16 and not by G,M,2
3657 You can use the tag 'all' to reject everything eg:
3663 but this probably for advanced users...
3664 <sect1>reject/route <call> [0-9] <pattern> (8)
3668 <bf>reject/route <call> [0-9] <pattern></bf> Set an 'reject' filter line for routing
3672 Create an 'reject this routing PC Protocol' line for a filter.
3674 An reject filter line means that if a PC16/17/19/21/24/41/50 matches this filter
3675 it is NOT passed thru that interface. See HELP FILTERING for more info. Please
3676 read this to understand how filters work - it will save a lot of grief later on.
3678 You can use any of the following things in this line:-
3681 call <prefixes> the callsign of the thingy
3682 call_dxcc <prefixes or numbers> eg: 61,62 (from eg: sh/pre G)
3683 call_itu <prefixes or numbers> or: G,GM,GW
3684 call_zone <prefixes or numbers>
3685 call_state <states> eg: VA,NH,RI,ME
3686 origin <prefixes> really the interface it came in on
3687 origin_dxcc <prefixes or numbers> eg: 61,62 (from eg: sh/pre G)
3688 origin_itu <prefixes or numbers> or: G,GM,GW
3689 origin_zone <prefixes or numbers>
3690 origin_state <states> eg: VA,NH,RI,ME
3696 rej/route gb7djk call_dxcc 61,38 (everything except UK+EIRE nodes)
3699 You can use the tag 'all' to reject everything eg:
3702 rej/route all (equiv to [very] restricted mode)
3705 as with ACCEPT/ROUTE 'by' is now a synonym for 'call'.
3706 <sect1>reject/spots <call> [input] [0-9] <pattern> (8)
3710 <bf>reject/spots <call> [input] [0-9] <pattern></bf> Spot filter sysop version
3714 This version allows a sysop to set a filter for a callsign as well as the
3715 default for nodes and users eg:-
3718 reject/spot db0sue-7 1 by_zone 14,15,16
3719 reject/spot node_default all
3720 set/hops node_default 10
3724 reject/spot user_default by G,M,2
3727 <sect1>reject/spots [0-9] <pattern> (0)
3731 <bf>reject/spots [0-9] <pattern></bf> Set a 'reject' filter line for spots
3735 Create a 'reject this spot' line for a filter.
3737 A reject filter line means that if the spot matches this filter it is
3738 dumped (not passed on). See HELP FILTERING for more info. Please read this
3739 to understand how filters work - it will save a lot of grief later on.
3741 You can use any of the following things in this line:-
3744 freq <range> eg: 0/30000 or hf or hf/cw or 6m,4m,2m
3745 on <range> same as 'freq'
3746 call <prefixes> eg: G,PA,HB9
3747 info <string> eg: iota or qsl
3749 call_dxcc <prefixes or numbers> eg: 61,62 (from eg: sh/pre G)
3750 call_itu <prefixes or numbers> or: G,GM,GW
3751 call_zone <prefixes or numbers>
3752 call_state <states> eg: VA,NH,RI,ME
3753 by_dxcc <prefixes or numbers>
3754 by_itu <prefixes or numbers>
3755 by_zone <prefixes or numbers>
3756 by_state <states> eg: VA,NH,RI,ME
3757 origin <prefixes>
3758 channel <prefixes>
3761 'call' means the callsign that has spotted 'by' whoever.
3763 For frequencies, you can use any of the band names defined in
3764 SHOW/BANDS and you can use a subband name like: cw, rtty, data, ssb -
3765 thus: hf/ssb. You can also just have a simple range like: 0/30000 -
3766 this is more efficient than saying simply: on HF (but don't get
3767 too hung up about that)
3773 rej/spot 2 on vhf and not (by_zone 14,15,16 or call_zone 14,15,16)
3776 You can use the tag 'all' to reject everything eg:
3782 but this probably for advanced users...
3783 <sect1>reject/wcy <call> [input] [0-9] <pattern> (8)
3787 <bf>reject/wcy <call> [input] [0-9] <pattern></bf> WCY filter sysop version
3791 This version allows a sysop to set a filter for a callsign as well as the
3792 default for nodes and users eg:-
3795 reject/wcy gb7djk all
3798 <sect1>reject/wcy [0-9] <pattern> (0)
3802 <bf>reject/wcy [0-9] <pattern></bf> set a 'reject' WCY filter
3806 It is unlikely that you will want to do this, but if you do then you can
3807 filter on the following fields:-
3810 by <prefixes> eg: G,M,2
3811 origin <prefixes>
3812 origin_dxcc <prefixes or numbers> eg: 61,62 (from eg: sh/pre G)
3813 origin_itu <prefixes or numbers> or: G,GM,GW
3814 origin_zone <prefixes or numbers>
3815 by_dxcc <prefixes or numbers>
3816 by_itu <prefixes or numbers>
3817 by_zone <prefixes or numbers>
3818 channel <prefixes>
3821 There are no examples because WCY Broadcasts only come from one place and
3822 you either want them or not (see UNSET/WCY if you don't want them).
3824 This command is really provided for future use.
3826 See HELP FILTER for information.
3827 <sect1>reject/wwv <call> [input] [0-9] <pattern> (8)
3831 <bf>reject/wwv <call> [input] [0-9] <pattern></bf> WWV filter sysop version
3835 This version allows a sysop to set a filter for a callsign as well as the
3836 default for nodes and users eg:-
3839 reject/wwv db0sue-7 1 by_zone 4
3840 reject/wwv node_default all
3844 reject/wwv user_default by W
3847 <sect1>reject/wwv [0-9] <pattern> (0)
3851 <bf>reject/wwv [0-9] <pattern></bf> set a 'reject' WWV filter
3855 It is unlikely that you will want to do this, but if you do then you can
3856 filter on the following fields:-
3859 by <prefixes> eg: G,M,2
3860 origin <prefixes>
3861 origin_dxcc <prefixes or numbers> eg: 61,62 (from eg: sh/pre G)
3862 origin_itu <prefixes or numbers> or: G,GM,GW
3863 origin_zone <prefixes or numbers>
3864 by_dxcc <prefixes or numbers>
3865 by_itu <prefixes or numbers>
3866 by_zone <prefixes or numbers>
3867 channel <prefixes>
3873 reject/wwv by_zone 14,15,16
3876 is probably the only useful thing to do (which will only show WWV broadcasts
3877 by stations in the US).
3879 See HELP FILTER for information.
3884 <bf>reply</bf> Reply (privately) to the last message that you have read
3888 <sect1>reply <msgno> (0)
3892 <bf>reply <msgno></bf> Reply (privately) to the specified message
3896 <sect1>reply b <msgno> (0)
3900 <bf>reply b <msgno></bf> Reply as a Bulletin to the specified message
3904 <sect1>reply noprivate <msgno> (0)
3908 <bf>reply noprivate <msgno></bf> Reply as a Bulletin to the specified message
3912 <sect1>reply rr <msgno> (0)
3916 <bf>reply rr <msgno></bf> Reply to the specified message with read receipt
3920 You can reply to a message and the subject will automatically have
3921 "Re:" inserted in front of it, if it isn't already present.
3923 You can also use all the extra qualifiers such as RR, PRIVATE,
3924 NOPRIVATE, B that you can use with the SEND command (see SEND
3925 for further details)
3926 <sect1>save [-d -t -a] <filename> "<cmd>" [...] (9)
3930 <bf>save [-d -t -a] <filename> "<cmd>" [...]</bf> Save command output to a file
3934 This sysop only cammand allows you to save the output of one or more
3935 commands to a file. For example:-
3938 save /spider/packclus/dxstats show/dxstat
3941 will save the output of the normal command "show/dxstat" to the file
3942 "dxstats" in the files area.
3944 You can have some extra flags to the save which will either
3945 date stamp or time stamp or both the filename so:-
3948 save -d /tmp/a <cmd> creates /tmp/a_6-Jan-2002
3949 save -t /tmp/a <cmd> creates /tmp/a_2301Z
3950 save -d -t /tmp/a <cmd> creates /tmp/a_6-Jan-2002_2301Z
3953 The -a flag means append to the file instead of overwriting it.
3955 You can have more than one command on the line, to do this you MUST
3956 enclose each command in double quotes (") eg:-
3959 save /tmp/a "sh/hfstats" "blank +" "sh/vhfstats"
3965 save /tmp/a "sh/hfstats","blank +","sh/vhfstats"
3968 You can only write into places that the cluster has permission for (which
3969 is that of the "sysop" user [which had BETTER NOT BE "root"]), you will
3970 need to create any directories you want to put stuff in beforehand as well.
3972 It is likely that you will want to run these commands in a crontab type
3973 situation. You would do that something like:-
3976 0 0 * * * run_cmd('save /tmp/dxstats "echo DXStat Table", "sh/dxstats"')
3979 Note that you still enclose each command with (") characters but you must
3980 enclose the entire save command in (') characters.
3982 Now in fact, this can be varied if you know what you are doing. See the
3983 admin manual for more details.
3985 <sect1>send <call> [<call> ...] (0)
3989 <bf>send <call> [<call> ...]</bf> Send a message to one or more callsigns
3993 <sect1>send copy <msgno> <call> (0)
3997 <bf>send copy <msgno> <call></bf> Send a copy of a message to someone
4001 <sect1>send noprivate <call> (0)
4005 <bf>send noprivate <call></bf> Send a message to all stations
4009 All the SEND commands will create a message which will be sent either to
4010 an individual callsign or to one of the 'bulletin' addresses.
4012 SEND <call> on its own acts as though you had typed SEND PRIVATE, that is
4013 it will mark the message as personal and send it to the cluster node that
4014 that callsign is connected to. If the <call> you have specified is in fact
4015 a known bulletin category on your node (eg: ALL) then the message should
4016 automatically become a bulletin.
4018 You can have more than one callsign in all of the SEND commands.
4020 You can have multiple qualifiers so that you can have for example:-
4023 SEND RR COPY 123 PRIVATE G1TLH G0RDI
4026 which should send a copy of message 123 to G1TLH and G0RDI and you will
4027 receive a read receipt when they have read the message.
4029 SB is an alias for SEND NOPRIVATE (or send a bulletin in BBS speak)
4030 SP is an alias for SEND PRIVATE
4032 The system will ask you for a subject. Conventionally this should be
4033 no longer than 29 characters for compatibility. Most modern cluster
4034 software should accept more.
4036 You will now be prompted to start entering your text.
4038 You finish the message by entering '/EX' on a new line. For instance:
4047 If you have started a message and you don't want to keep it then you
4048 can abandon the message with '/ABORT' on a new line, like:-
4053 oh I just can't be bothered with this
4057 If you abort the message it will NOT be sent.
4059 When you are entering the text of your message, most normal output (such
4060 as DX announcements and so on are suppressed and stored for latter display
4061 (upto 20 such lines are stored, as new ones come along, so the oldest
4064 Also, you can enter normal commands commands (and get the output
4065 immediately) whilst in the middle of a message. You do this by typing
4066 the command preceeded by a '/' character on a new line, so:-
4069 /dx g1tlh 144010 strong signal
4072 Will issue a dx annoucement to the rest of the cluster.
4074 Also, you can add the output of a command to your message by preceeding
4075 the command with '//', thus :-
4081 This will show YOU the output from SH/VHFTABLE and also store it in the
4084 You can carry on with the message until you are ready to send it.
4085 <sect1>send private <call> (0)
4089 <bf>send private <call></bf> Send a personal message
4093 <sect1>send rr <call> (0)
4097 <bf>send rr <call></bf> Send a message and ask for a read receipt
4101 <sect1>set/address <your address> (0)
4105 <bf>set/address <your address></bf> Record your postal address
4109 <sect1>set/announce (0)
4113 <bf>set/announce</bf> Allow announce messages to come out on your terminal
4117 <sect1>set/anntalk (0)
4121 <bf>set/anntalk</bf> Allow talk like announce messages on your terminal
4125 <sect1>set/arcluster <call> [<call>..] (5)
4129 <bf>set/arcluster <call> [<call>..]</bf> Make the callsign an AR-Cluster node
4133 <sect1>set/baddx <call>.. (8)
4137 <bf>set/baddx <call>..</bf> Stop callsigns in a dx spot being propagated
4141 <sect1>set/badnode <call>.. (8)
4145 <bf>set/badnode <call>..</bf> Stop spots from this node being propagated
4149 <sect1>set/badspotter <call>.. (8)
4153 <bf>set/badspotter <call>..</bf> Stop spots from this callsign being propagated
4157 <sect1>set/badword <word>.. (8)
4161 <bf>set/badword <word>..</bf> Stop things with this word being propagated
4165 <sect1>set/bbs <call> [<call>..] (5)
4169 <bf>set/bbs <call> [<call>..]</bf> Make the callsign a BBS
4177 <bf>set/beep</bf> Add a beep to DX and other messages on your terminal
4181 <sect1>set/clx <call> [<call>..] (5)
4185 <bf>set/clx <call> [<call>..]</bf> Make the callsign an CLX node
4189 <sect1>set/debug <name> (9)
4193 <bf>set/debug <name></bf> Add a debug level to the debug set
4201 <bf>set/dx</bf> Allow DX messages to come out on your terminal
4209 <bf>set/dxcq</bf> Show CQ Zones on the end of DX announcements
4213 <sect1>set/dxgrid (0)
4217 <bf>set/dxgrid</bf> Allow QRA Grid Squares on the end of DX announcements
4221 <sect1>set/dxitu (0)
4225 <bf>set/dxitu</bf> Show ITU Zones on the end of DX announcements
4229 <sect1>set/dxnet <call> [<call>..] (5)
4233 <bf>set/dxnet <call> [<call>..]</bf> Make the callsign an DXNet node
4241 <bf>set/echo</bf> Make the cluster echo your input
4245 <sect1>set/email <email> ... (0)
4249 <bf>set/email <email> ...</bf> Set email address(es) and forward your personals
4257 <bf>set/here</bf> Tell the system you are present at your terminal
4261 <sect1>set/homenode <node> (0)
4265 <bf>set/homenode <node> </bf> Set your normal cluster callsign
4269 Tell the cluster system where you normally connect to. Any Messages sent
4270 to you will normally find their way there should you not be connected.
4276 <sect1>set/hops <call> ann|spots|route|wwv|wcy <n> (8)
4280 <bf>set/hops <call> ann|spots|route|wwv|wcy <n></bf> Set hop count
4284 <sect1>set/isolate (9)
4288 <bf>set/isolate</bf> Isolate a node from the rest of the network
4292 Connect a node to your system in such a way that you are a full protocol
4293 member of its network and can see all spots on it, but nothing either leaks
4294 out from it nor goes back into from the rest of the nodes connected to you.
4296 You can potentially connect several nodes in this way.
4298 <sect1>set/language <lang> (0)
4302 <bf>set/language <lang></bf> Set the language you want to use
4306 You can select the language that you want the cluster to use. Currently
4307 the languages available are en (English), de (German), es (Spanish)
4309 <sect1>set/location <lat & long> (0)
4313 <bf>set/location <lat & long></bf> Set your latitude and longitude
4317 <sect1>set/lockout <call> (9)
4321 <bf>set/lockout <call></bf> Stop a callsign connecting to the cluster
4325 <sect1>set/logininfo (0)
4329 <bf>set/logininfo</bf> Inform when a station logs in locally
4333 <sect1>set/name <your name> (0)
4337 <bf>set/name <your name></bf> Set your name
4341 Tell the system what your name is eg:-
4346 <sect1>set/node <call> [<call>..] (5)
4350 <bf>set/node <call> [<call>..]</bf> Make the callsign an AK1A cluster
4354 Tell the system that the call(s) are to be treated as AK1A cluster and
4355 fed PC Protocol rather normal user commands.
4356 <sect1>set/obscount <count> <call> (8)
4360 <bf>set/obscount <count> <call></bf> Set the 'pump-up' obscelence PING counter
4364 From 1.35 onwards neighbouring nodes are pinged at regular intervals (see
4365 SET/PINGINTERVAL), usually 300 seconds or 5 minutes. There is a 'pump-up'
4366 counter which is decremented on every outgoing ping and then reset to
4367 the 'obscount' value on every incoming ping. The default value of this
4370 What this means is that a neighbouring node will be pinged twice at
4371 (default) 300 second intervals and if no reply has been heard just before
4372 what would be the third attempt, that node is disconnected.
4374 If a ping is heard then the obscount is reset to the full value. Using
4375 default values, if a node has not responded to a ping within 15 minutes,
4378 You can set this parameter between 1 and 9.
4380 It is STRONGLY recommended that you don't change the default.
4381 <sect1>set/page <lines per page> (0)
4385 <bf>set/page <lines per page></bf> Set the lines per page
4389 Tell the system how many lines you wish on a page when the number of line
4390 of output from a command is more than this. The default is 20. Setting it
4391 explicitly to 0 will disable paging.
4397 The setting is stored in your user profile.
4398 <sect1>set/password (0)
4402 <bf>set/password</bf> Set your own password
4406 This command only works for a 'telnet' user (currently). It will
4407 only work if you have a password already set. This initial password
4408 can only be set by the sysop.
4410 When you execute this command it will ask you for your old password,
4411 then ask you to type in your new password twice (to make sure you
4412 get it right). You may or may not see the data echoed on the screen
4413 as you type, depending on the type of telnet client you have.
4414 <sect1>set/password <callsign> <string> (9)
4418 <bf>set/password <callsign> <string></bf> Set a users password
4422 The password for a user can only be set by a full sysop. The string
4423 can contain any characters.
4425 The way this field is used depends on context. If it is being used in
4426 the SYSOP command context then you are offered 5 random numbers and you
4427 have to supply the corresponding letters. This is now mainly for ax25
4430 If it is being used on incoming telnet connections then, if a password
4434 set/var $main::passwdreq = 1
4437 command is executed in the startup script, then a password prompt is
4438 given after the normal 'login: ' prompt.
4439 <sect1>set/pinginterval <time> <nodecall> (9)
4443 <bf>set/pinginterval <time> <nodecall></bf> Set ping time to neighbouring nodes
4447 As from release 1.35 all neighbouring nodes are pinged at regular intervals
4448 in order to determine the rolling quality of the link and, in future, to
4449 affect routing decisions. The default interval is 300 secs or 5 minutes.
4451 You can use this command to set a different interval. Please don't.
4453 But if you do the value you enter is treated as minutes up 30 and seconds
4454 for numbers greater than that.
4456 This is used also to help determine when a link is down at the far end
4457 (as certain cluster software doesn't always notice), see SET/OBSCOUNT
4458 for more information.
4460 If you must change it (and it may be useful for internet connected nodes
4461 on dynamic IP addresses that go away after a set time of usage) the time
4462 can be specified as:-
4465 5 which if less than 30 is converted to minutes otherwise is
4466 taken as the no of seconds between pings.
4472 Please be aware that this causes traffic to occur on the link, setting
4473 this value too low may annoy your neighbours beyond the point of
4476 You can switch this off by setting it to 0.
4477 <sect1>set/privilege <n> <call> [<call..] (9)
4481 <bf>set/privilege <n> <call> [<call..]</bf> Set privilege level on a call
4485 Set the privilege level on a callsign. The privilege levels that pertain
4486 to commands are as default:-
4489 1 - allow remote nodes normal user RCMDs
4490 5 - various privileged commands (including shutdown, but not disc-
4491 connect), the normal level for another node.
4492 8 - more privileged commands (including disconnect)
4493 9 - local sysop privilege. DO NOT SET ANY REMOTE USER OR NODE TO THIS
4496 If you are a sysop and you come in as a normal user on a remote connection
4497 your privilege will automatically be set to 0.
4498 <sect1>set/prompt <string> (0)
4502 <bf>set/prompt <string></bf> Set your prompt to <string>
4506 <sect1>set/qra <locator> (0)
4510 <bf>set/qra <locator></bf> Set your QRA Grid locator
4514 Tell the system what your QRA (or Maidenhead) locator is. If you have not
4515 done a SET/LOCATION then your latitude and longitude will be set roughly
4516 correctly (assuming your locator is correct ;-). For example:-
4521 <sect1>set/qth <your qth> (0)
4525 <bf>set/qth <your qth></bf> Set your QTH
4529 Tell the system where you are. For example:-
4531 SET/QTH East Dereham, Norfolk
4534 <sect1>set/register <call> ... (9)
4538 <bf>set/register <call> ...</bf> Mark a user as registered
4542 <sect1>set/spider <call> [<call>..] (5)
4546 <bf>set/spider <call> [<call>..]</bf> Make the callsign an DXSpider node
4550 Tell the system that the call(s) are to be treated as DXSpider node and
4551 fed new style DX Protocol rather normal user commands.
4552 <sect1>set/sys_location <lat & long> (9)
4556 <bf>set/sys_location <lat & long></bf> Set your cluster latitude and longitude
4560 In order to get accurate headings and such like you must tell the system
4561 what your latitude and longitude is. If you have not yet done a SET/QRA
4562 then this command will set your QRA locator for you. For example:-
4564 SET/LOCATION 52 22 N 0 57 E
4567 <sect1>set/sys_qra <locator> (9)
4571 <bf>set/sys_qra <locator></bf> Set your cluster QRA Grid locator
4579 <bf>set/talk</bf> Allow TALK messages to come out on your terminal
4583 <sect1>set/usdb <call> <state> <city> (9)
4587 <bf>set/usdb <call> <state> <city></bf> add/update a US DB callsign
4591 This command allows you to add or alter a callsign in the US state
4592 database. Use with extreme caution. Anything you do here will be
4593 overwritten by any weekly updates that affect this callsign
4596 set/usdb g1tlh nh downtown rindge
4599 see also DELETE/USDB
4600 <sect1>set/usstate (0)
4604 <bf>set/usstate</bf> Allow US State info on the end of DX announcements
4612 <bf>set/wcy</bf> Allow WCY messages to come out on your terminal
4620 <bf>set/wwv</bf> Allow WWV messages to come out on your terminal
4628 <bf>set/wx</bf> Allow WX messages to come out on your terminal
4632 <sect1>show/baddx (1)
4636 <bf>show/baddx</bf> Show all the bad dx calls in the system
4640 Display all the bad dx callsigns in the system, see SET/BADDX
4641 for more information.
4642 <sect1>show/badnode (1)
4646 <bf>show/badnode</bf> Show all the bad nodes in the system
4650 Display all the bad node callsigns in the system, see SET/BADNODE
4651 for more information.
4652 <sect1>show/badspotter (1)
4656 <bf>show/badspotter</bf> Show all the bad spotters in the system
4660 Display all the bad spotter's callsigns in the system, see SET/BADSPOTTER
4661 for more information.
4662 <sect1>show/badword (1)
4666 <bf>show/badword</bf> Show all the bad words in the system
4670 Display all the bad words in the system, see SET/BADWORD
4671 for more information.
4672 <sect1>show/chat [<group>] [<lines>] (0)
4676 <bf>show/chat [<group>] [<lines>]</bf> Show any chat or conferencing
4680 This command allows you to see any chat or conferencing that has
4681 occurred whilst you were away. SHOW/CHAT on its own will show data for
4682 all groups. If you use a group name then it will show only chat for
4684 <sect1>show/configuration [<node>] (0)
4688 <bf>show/configuration [<node>]</bf> Show all the nodes and users visible
4692 This command allows you to see all the users that can be seen
4693 and the nodes to which they are connected.
4695 This command is normally abbreviated to: sh/c
4697 Normally, the list returned will be just for the nodes from your
4698 country (because the list otherwise will be very long).
4704 will produce a complete list of all nodes.
4706 BE WARNED: the list that is returned can be VERY long
4708 It is possible to supply a node or part of a prefix and you will get
4709 a list of the users for that node or list of nodes starting with
4720 <sect1>show/configuration/node (0)
4724 <bf>show/configuration/node</bf> Show all the nodes connected locally
4728 Show all the nodes connected to this node.
4729 <sect1>show/connect (1)
4733 <bf>show/connect</bf> Show all the active connections
4737 This command shows information on all the active connections known to
4738 the node. This command gives slightly more information than WHO.
4739 <sect1>show/contest <year and month> (0)
4743 <bf>show/contest <year and month></bf> Show all the contests for a month
4747 Show all known contests which are maintained at http://www.sk3bg.se/contest/
4748 for a particular month or year. The format is reasonably flexible.
4756 <sect1>show/date [<prefix>|<callsign>] (0)
4760 <bf>show/date [<prefix>|<callsign>]</bf> Show the local time
4764 This is very nearly the same as SHOW/TIME, the only difference the format
4765 of the date string if no arguments are given.
4767 If no prefixes or callsigns are given then this command returns the local
4768 time and UTC as the computer has it right now. If you give some prefixes
4769 then it will show UTC and UTC + the local offset (not including DST) at
4770 the prefixes or callsigns that you specify.
4771 <sect1>show/db0sdx <callsign> (0)
4775 <bf>show/db0sdx <callsign></bf> Show QSL infomation from DB0SDX database
4779 This command queries the DB0SDX QSL server on the internet
4780 and returns any information available for that callsign. This service
4781 is provided for users of this software by http://www.qslinfo.de.
4783 See also SHOW/QRZ, SHOW/WM7D.
4784 <sect1>show/debug (9)
4788 <bf>show/debug</bf> Show what levels of debug information you are logging
4796 <bf>show/dx</bf> Interrogate the spot database
4800 If you just type SHOW/DX you will get the last so many spots
4801 (sysop configurable, but usually 10).
4803 In addition you can add any number of these commands in very nearly
4804 any order to the basic SHOW/DX command, they are:-
4807 on <band> - eg 160m 20m 2m 23cm 6mm
4808 on <region> - eg hf vhf uhf shf (see SHOW/BANDS)
4809 on <from>/<to> - eg 1000/4000 14000-30000 (in Khz)
4810 <from>-<to>
4814 <number> - the number of spots you want
4815 <from>-<to> - <from> spot no <to> spot no in the selected list
4816 <from>/<to>
4820 <prefix> - for a spotted callsign beginning with <prefix>
4821 *<suffix> - for a spotted callsign ending in <suffix>
4822 *<string>* - for a spotted callsign containing <string>
4826 day <number> - starting <number> days ago
4827 day <from>-<to> - <from> days <to> days ago
4828 <from>/<to>
4832 info <text> - any spots containing <text> in the info or remarks
4836 by <call> - any spots spotted by <call> (spotter <call> is the
4841 qsl - this automatically looks for any qsl info on the call
4842 held in the spot database.
4846 iota [<iota>] - If the iota island number is missing it will look for
4847 the string iota and anything which looks like an iota
4848 island number. If you specify then it will look for
4853 qra [<locator>] - this will look for the specific locator if you specify
4854 one or else anything that looks like a locator.
4858 dxcc - treat the prefix as a 'country' and look for spots
4859 from that country regardless of actual prefix.
4864 You can also use this with the 'by' keyword so
4874 SH/DX on 20m info iota
4875 SH/DX 9a on vhf day 30
4881 SH/DX dxcc oq2 by w dxcc
4884 <sect1>show/dxcc <prefix> (0)
4888 <bf>show/dxcc <prefix></bf> Interrogate the spot database by country
4892 This command takes the <prefix> (which can be a full or partial
4893 callsign if desired), looks up which internal country number it is
4894 and then displays all the spots as per SH/DX for that country.
4896 This is now an alias for 'SHOW/DX DXCC'
4898 The options for SHOW/DX also apply to this command.
4903 SH/DXCC W on 20m iota
4906 This can be done with the SHOW/DX command like this:-
4910 SH/DX dxcc w on 20m iota
4913 <sect1>show/dxqsl <callsign> (0)
4917 <bf>show/dxqsl <callsign></bf> Show any QSL info gathered from spots
4921 The node collects information from the comment fields in spots (things
4922 like 'VIA EA7WA' or 'QSL-G1TLH') and stores these in a database.
4924 This command allows you to interrogate that database and if the callsign
4925 is found will display the manager(s) that people have spotted. This
4926 information is NOT reliable, but it is normally reasonably accurate if
4927 it is spotted enough times.
4935 You can check the raw input spots yourself with:-
4941 This gives you more background information.
4942 <sect1>show/dxstats [days] [date] (0)
4946 <bf>show/dxstats [days] [date]</bf> Show the DX Statistics
4950 Show the total DX spots for the last <days> no of days (default is 31),
4951 starting from a <date> (default: today).
4952 <sect1>show/files [<filearea> [<string>]] (0)
4956 <bf>show/files [<filearea> [<string>]]</bf> List the contents of a filearea
4960 SHOW/FILES on its own will show you a list of the various fileareas
4961 available on the system. To see the contents of a particular file
4964 SH/FILES <filearea>
4966 where <filearea> is the name of the filearea you want to see the
4969 You can also use shell globbing characters like '*' and '?' in a
4970 string to see a selection of files in a filearea eg:-
4972 SH/FILES bulletins arld*
4975 See also TYPE - to see the contents of a file.
4976 <sect1>show/filter (0)
4980 <bf>show/filter</bf> Show the contents of all the filters you have set
4984 Show the contents of all the filters that are set. This command displays
4985 all the filters set - for all the various categories.
4986 <sect1>show/hfstats [days] [date] (0)
4990 <bf>show/hfstats [days] [date]</bf> Show the HF DX Statistics
4994 Show the HF DX spots breakdown by band for the last <days> no of days
4995 (default is 31), starting from a <date> (default: today).
4996 <sect1>show/hftable [days] [date] [prefix ...] (0)
5000 <bf>show/hftable [days] [date] [prefix ...]</bf> Show the HF DX Spotter Table
5004 Show the HF DX Spotter table for the list of prefixes for the last
5005 <days> no of days (default is 31), starting from a <date> (default: today).
5007 If there are no prefixes then it will show the table for your country.
5009 Remember that some countries have more than one "DXCC country" in them
5010 (eg G :-), to show them (assuming you are not in G already which is
5011 specially treated in the code) you must list all the relevant prefixes
5014 sh/hftable g gm gd gi gj gw gu
5017 Note that the prefixes are converted into country codes so you don't have
5018 to list all possible prefixes for each country.
5020 If you want more or less days than the default simply include the
5021 number you require:-
5027 If you want to start at a different day, simply add the date in some
5031 sh/hftable 2 25nov02
5032 sh/hftable 2 25-nov-02
5034 sh/hftable 2 25/11/02
5037 This will show the stats for your DXCC for that CQWW contest weekend.
5039 You can specify either prefixes or full callsigns (so you can see how you
5040 did against all your mates). You can also say 'all' which will then print
5041 the worldwide statistics.
5047 <sect1>show/hops <call> [ann|spots|route|wcy|wwv] (8)
5051 <bf>show/hops <call> [ann|spots|route|wcy|wwv]</bf> Show the hop counts for a node
5055 This command shows the hop counts set up for a node. You can specify
5056 which category you want to see. If you leave the category out then
5057 all the categories will be listed.
5059 <sect1>show/isolate (1)
5063 <bf>show/isolate</bf> Show list of ISOLATED nodes
5067 <sect1>show/lockout <prefix>|all (9)
5071 <bf>show/lockout <prefix>|all</bf> Show the list of locked out or excluded callsigns
5075 <sect1>show/log [<callsign>] (8)
5079 <bf>show/log [<callsign>]</bf> Show excerpts from the system log
5083 This command outputs a short section of the system log. On its own
5084 it will output a general logfile. With the optional callsign it will
5085 show output from the log associated with that callsign.
5086 <sect1>show/moon [ndays] [<prefix>|<callsign>] (0)
5090 <bf>show/moon [ndays] [<prefix>|<callsign>]</bf> Show Moon rise and set times
5094 Show the Moon rise and set times for a (list of) prefixes or callsigns,
5095 together with the azimuth and elevation of the sun currently at those
5098 If you don't specify any prefixes or callsigns, it will show the times for
5099 your QTH (assuming you have set it with either SET/LOCATION or SET/QRA),
5100 together with the current azimuth and elevation.
5102 In addition, it will show the illuminated fraction of the moons disk.
5104 If all else fails it will show the Moonrise and set times for the node
5105 that you are connected to.
5114 You can also use this command to see into the past or the future, so
5115 if you want to see yesterday's times then do:-
5121 or in three days time:-
5127 Upto 366 days can be checked both in the past and in the future.
5129 Please note that the rise and set times are given as the UT times of rise and
5130 set on the requested UT day.
5131 <sect1>show/muf <prefix> [<hours>][long] (0)
5135 <bf>show/muf <prefix> [<hours>][long]</bf> Show the likely propagation to a prefix
5139 This command allow you to estimate the likelihood of you contacting
5140 a station with the prefix you have specified. The output assumes a modest
5141 power of 20dBW and receiver sensitivity of -123dBm (about 0.15muV/10dB SINAD)
5143 The result predicts the most likely operating frequencies and signal
5144 levels for high frequency (shortwave) radio propagation paths on
5145 specified days of the year and hours of the day. It is most useful for
5146 paths between 250 km and 6000 km, but can be used with reduced accuracy
5147 for paths shorter or longer than this.
5149 The command uses a routine MINIMUF 3.5 developed by the U.S. Navy and
5150 used to predict the MUF given the predicted flux, day of the year,
5151 hour of the day and geographic coordinates of the transmitter and
5152 receiver. This routine is reasonably accurate for the purposes here,
5153 with a claimed RMS error of 3.8 MHz, but much smaller and less complex
5154 than the programs used by major shortwave broadcasting organizations,
5155 such as the Voice of America.
5157 The command will display some header information detailing its
5158 assumptions, together with the locations, latitude and longitudes and
5159 bearings. It will then show UTC (UT), local time at the other end
5160 (LT), calculate the MUFs, Sun zenith angle at the midpoint of the path
5161 (Zen) and the likely signal strengths. Then for each frequency for which
5162 the system thinks there is a likelihood of a circuit it prints a value.
5164 The value is currently a likely S meter reading based on the conventional
5165 6dB / S point scale. If the value has a '+' appended it means that it is
5166 1/2 an S point stronger. If the value is preceeded by an 'm' it means that
5167 there is likely to be much fading and by an 's' that the signal is likely
5170 By default SHOW/MUF will show the next two hours worth of data. You
5171 can specify anything up to 24 hours worth of data by appending the no of
5172 hours required after the prefix. For example:-
5181 RxSens: -123 dBM SFI: 159 R: 193 Month: 10 Day: 21
5182 Power : 20 dBW Distance: 6283 km Delay: 22.4 ms
5183 Location Lat / Long Azim
5184 East Dereham, Norfolk 52 41 N 0 57 E 47
5185 United-States-W 43 0 N 87 54 W 299
5186 UT LT MUF Zen 1.8 3.5 7.0 10.1 14.0 18.1 21.0 24.9 28.0 50.0
5187 18 23 11.5 -35 mS0+ mS2 S3
5188 19 0 11.2 -41 mS0+ mS2 S3
5191 indicating that you will have weak, fading circuits on top band and
5192 80m but usable signals on 40m (about S3).
5200 will get you the above display, but with the next 24 hours worth of
5208 Gives you an estimate of the long path propagation characterics. It
5209 should be noted that the figures will probably not be very useful, nor
5210 terrible accurate, but it is included for completeness.
5211 <sect1>show/newconfiguration [<node>] (0)
5215 <bf>show/newconfiguration [<node>]</bf> Show all the nodes and users visible
5219 This command allows you to see all the users that can be seen
5220 and the nodes to which they are connected.
5222 This command produces essentially the same information as
5223 SHOW/CONFIGURATION except that it shows all the duplication of
5224 any routes that might be present It also uses a different format
5225 which may not take up quite as much space if you don't have any
5228 BE WARNED: the list that is returned can be VERY long
5229 <sect1>show/newconfiguration/node (0)
5233 <bf>show/newconfiguration/node</bf> Show all the nodes connected locally
5237 Show all the nodes connected to this node in the new format.
5238 <sect1>show/node [<callsign> ...] (1)
5242 <bf>show/node [<callsign> ...]</bf> Show the type and version number of nodes
5246 Show the type and version (if connected) of the nodes specified on the
5247 command line. If no callsigns are specified then a sorted list of all
5248 the non-user callsigns known to the system will be displayed.
5249 <sect1>show/prefix <callsign> (0)
5253 <bf>show/prefix <callsign></bf> Interrogate the prefix database
5257 This command takes the <callsign> (which can be a full or partial
5258 callsign or a prefix), looks up which internal country number
5259 it is and then displays all the relevant prefixes for that country
5260 together with the internal country no, the CQ and ITU regions.
5263 <sect1>show/program (5)
5267 <bf>show/program</bf> Show the locations of all the included program modules
5271 Show the name and location where every program module was load from. This
5272 is useful for checking where you think you have loaded a .pm file from.
5273 <sect1>show/qra <lat> <long> (0)
5277 <bf>show/qra <lat> <long></bf> Convert lat/long to a QRA Grid locator
5281 This is a multipurpose command that allows you either to calculate the
5282 distance and bearing between two locators or (if only one locator is
5283 given on the command line) the distance and beraing from your station
5284 to the locator. For example:-
5291 The first example will show the distance and bearing to the locator from
5292 yourself, the second example will calculate the distance and bearing from
5293 the first locator to the second. You can use 4 or 6 character locators.
5295 It is also possible to convert a latitude and longitude to a locator by
5296 using this command with a latitude and longitude as an argument, for
5300 SH/QRA 52 41 N 0 58 E
5303 <sect1>show/qra <locator> [<locator>] (0)
5307 <bf>show/qra <locator> [<locator>]</bf> Show distance between QRA Grid locators
5311 <sect1>show/qrz <callsign> (0)
5315 <bf>show/qrz <callsign></bf> Show any callbook details on a callsign
5319 This command queries the QRZ callbook server on the internet
5320 and returns any information available for that callsign. This service
5321 is provided for users of this software by http://www.qrz.com
5323 See also SHOW/WM7D for an alternative.
5324 <sect1>show/registered [<prefix>] (9)
5328 <bf>show/registered [<prefix>]</bf> Show the registered users
5332 <sect1>show/route <callsign> ... (0)
5336 <bf>show/route <callsign> ...</bf> Show the route to the callsign
5340 This command allows you to see to which node the callsigns specified are
5341 connected. It is a sort of inverse sh/config.
5347 <sect1>show/satellite <name> [<hours> <interval>] (0)
5351 <bf>show/satellite <name> [<hours> <interval>]</bf> Show tracking data
5355 Show the tracking data from your location to the satellite of your choice
5356 from now on for the next few hours.
5358 If you use this command without a satellite name it will display a list
5359 of all the satellites known currently to the system.
5361 If you give a name then you can obtain tracking data of all the passes
5362 that start and finish 5 degrees below the horizon. As default it will
5363 give information for the next three hours for every five minute period.
5365 You can alter the number of hours and the step size, within certain
5368 Each pass in a period is separated with a row of '-----' characters
5374 SH/SAT FENGYUN1 12 2
5377 <sect1>show/station all [<regex>] (6)
5381 <bf>show/station all [<regex>]</bf> Show list of users in the system
5385 <sect1>show/station [<callsign> ..] (0)
5389 <bf>show/station [<callsign> ..]</bf> Show information about a callsign
5393 Show the information known about a callsign and whether (and where)
5394 that callsign is connected to the cluster.
5400 If no callsign is given then show the information for yourself.
5401 <sect1>show/sun [ndays] [<prefix>|<callsign>] (0)
5405 <bf>show/sun [ndays] [<prefix>|<callsign>]</bf> Show sun rise and set times
5409 Show the sun rise and set times for a (list of) prefixes or callsigns,
5410 together with the azimuth and elevation of the sun currently at those
5413 If you don't specify any prefixes or callsigns, it will show the times for
5414 your QTH (assuming you have set it with either SET/LOCATION or SET/QRA),
5415 together with the current azimuth and elevation.
5417 If all else fails it will show the sunrise and set times for the node
5418 that you are connected to.
5424 SH/SUN G1TLH K9CW ZS
5427 You can also use this command to see into the past or the future, so
5428 if you want to see yesterday's times then do:-
5434 or in three days time:-
5440 Upto 366 days can be checked both in the past and in the future.
5442 Please note that the rise and set times are given as the UT times of rise
5443 and set on the requested UT day.
5444 <sect1>show/time [<prefix>|<callsign>] (0)
5448 <bf>show/time [<prefix>|<callsign>]</bf> Show the local time
5452 If no prefixes or callsigns are given then this command returns the local
5453 time and UTC as the computer has it right now. If you give some prefixes
5454 then it will show UTC and UTC + the local offset (not including DST) at
5455 the prefixes or callsigns that you specify.
5456 <sect1>show/usdb [call ..] (0)
5460 <bf>show/usdb [call ..]</bf> Show information held on the FCC Call database
5464 Show the City and State of a Callsign held on the FCC database if
5465 his is being run on this system, eg:-
5471 <sect1>show/vhfstats [days] [date] (0)
5475 <bf>show/vhfstats [days] [date]</bf> Show the VHF DX Statistics
5479 Show the VHF DX spots breakdown by band for the last
5480 <days> no of days (default is 31), starting from a date (default: today).
5481 <sect1>show/vhftable [days] [date] [prefix ...] (0)
5485 <bf>show/vhftable [days] [date] [prefix ...]</bf> Show the VHF DX Spotter Table
5489 Show the VHF DX Spotter table for the list of prefixes for the last
5490 <days> no of days (default is 31), starting from a date (default: today).
5492 If there are no prefixes then it will show the table for your country.
5494 Remember that some countries have more than one "DXCC country" in them
5495 (eg G :-), to show them (assuming you are not in G already which is
5496 specially treated in the code) you must list all the relevant prefixes
5499 sh/vhftable g gm gd gi gj gw gu
5502 Note that the prefixes are converted into country codes so you don't have
5503 to list all possible prefixes for each country.
5505 If you want more or less days than the default simply include the
5506 number you require:-
5512 If you want to start at a different day, simply add the date in some
5516 sh/vhftable 2 25nov02
5517 sh/vhftable 2 25-nov-02
5518 sh/vhftable 2 021125
5519 sh/vhftable 2 25/11/02
5522 This will show the stats for your DXCC for that CQWW contest weekend.
5524 You can specify either prefixes or full callsigns (so you can see how you
5525 did against all your mates). You can also say 'all' which will then print
5526 the worldwide statistics.
5536 <bf>show/wcy</bf> Show last 10 WCY broadcasts
5540 <sect1>show/wcy <n> (0)
5544 <bf>show/wcy <n></bf> Show last <n> WCY broadcasts
5548 Display the most recent WCY information that has been received by the system
5550 <sect1>show/wm7d <callsign> (0)
5554 <bf>show/wm7d <callsign></bf> Show callbook details on a US callsigns
5558 This command queries the WM7D callbook server on the internet
5559 and returns any information available for that US callsign. This service
5560 is provided for users of this software by http://www.wm7d.net.
5567 <bf>show/wwv</bf> Show last 10 WWV broadcasts
5571 <sect1>show/wwv <n> (0)
5575 <bf>show/wwv <n></bf> Show last <n> WWV broadcasts
5579 Display the most recent WWV information that has been received by the system
5584 <bf>shutdown</bf> Shutdown the cluster
5588 Shutdown the cluster and disconnect all the users
5589 <sect1>spoof <call> <command> (9)
5593 <bf>spoof <call> <command></bf> Do a command as though you are another user
5597 This command is provided so that sysops can set a user's parameters without
5598 me having to write a special 'sysop' version for every user command. It
5599 allows you to pretend that you are doing the command as the user you specify.
5604 SPOOF G1TLH set/name Dirk
5605 SPOOF G1TLH set/qra JO02LQ
5608 <sect1>stat/channel [<callsign>] (5)
5612 <bf>stat/channel [<callsign>]</bf> Show the status of a channel on the cluster
5616 Show the internal status of the channel object either for the channel that
5617 you are on or else for the callsign that you asked for.
5619 Only the fields that are defined (in perl term) will be displayed.
5620 <sect1>stat/db <dbname> (5)
5624 <bf>stat/db <dbname></bf> Show the status of a database
5628 Show the internal status of a database descriptor.
5630 Depending on your privilege level you will see more or less information.
5631 This command is unlikely to be of much use to anyone other than a sysop.
5636 <bf>stat/msg</bf> Show the status of the message system
5640 <sect1>stat/msg <msgno> (1)
5644 <bf>stat/msg <msgno></bf> Show the status of a message
5648 This command shows the internal status of a message and includes information
5649 such as to whom it has been forwarded, its size, origin etc etc.
5651 If no message number is given then the status of the message system is
5653 <sect1>stat/route_node <callsign> (5)
5657 <bf>stat/route_node <callsign></bf> Show the data in a Route::Node object
5661 <sect1>stat/route_node all (5)
5665 <bf>stat/route_node all</bf> Show list of all Route::Node objects
5669 <sect1>stat/route_user <callsign> (5)
5673 <bf>stat/route_user <callsign></bf> Show the data in a Route::User object
5677 <sect1>stat/route_user all (5)
5681 <bf>stat/route_user all</bf> Show list of all Route::User objects
5685 <sect1>stat/user [<callsign>] (5)
5689 <bf>stat/user [<callsign>]</bf> Show the full status of a user
5693 Shows the full contents of a user record including all the secret flags
5696 Only the fields that are defined (in perl term) will be displayed.
5701 <bf>sysop</bf> Regain your privileges if you login remotely
5705 The system automatically reduces your privilege level to that of a
5706 normal user if you login in remotely. This command allows you to
5707 regain your normal privilege level. It uses the normal system: five
5708 numbers are returned that are indexes into the character array that is
5709 your assigned password (see SET/PASSWORD). The indexes start from
5712 You are expected to return a string which contains the characters
5713 required in the correct order. You may intersperse those characters
5714 with others to obscure your reply for any watchers. For example (and
5715 these values are for explanation :-):
5718 password = 012345678901234567890123456789
5724 aa2bbbb0ccc5ddd7xxx3n
5729 They will all match. If there is no password you will still be offered
5730 numbers but nothing will happen when you input a string. Any match is
5732 <sect1>talk <call> > <node> [<text>] (0)
5736 <bf>talk <call> > <node> [<text>]</bf> Send a text message to another station via a node
5740 Send a short message to any other station that is visible on the cluster
5741 system. You can send it to anyone you can see with a SHOW/CONFIGURATION
5742 command, they don't have to be connected locally.
5744 The second form of TALK is used when other cluster nodes are connected
5745 with restricted information. This usually means that they don't send
5746 the user information usually associated with logging on and off the cluster.
5748 If you know that G3JNB is likely to be present on GB7TLH, but you can only
5749 see GB7TLH in the SH/C list but with no users, then you would use the
5750 second form of the talk message.
5752 If you want to have a ragchew with someone you can leave the text message
5753 out and the system will go into 'Talk' mode. What this means is that a
5754 short message is sent to the recipient telling them that you are in a
5755 'Talking' frame of mind and then you just type - everything you send will
5756 go to the station that you asked for.
5758 All the usual announcements, spots and so on will still come out on your
5761 If you want to do something (such as send a spot) you preceed the normal
5762 command with a '/' character, eg:-
5765 /DX 14001 G1TLH What's a B class licensee doing on 20m CW?
5769 To leave talk mode type:
5775 If you are in 'Talk' mode, there is an extention to the '/' command which
5776 allows you to send the output to all the people you are talking to. You do
5777 with the '//' command. For example:-
5783 will send the hftable as you have it to all the people you are currently
5785 <sect1>talk <call> [<text>] (0)
5789 <bf>talk <call> [<text>]</bf> Send a text message to another station
5793 <sect1>type <filearea>/<name> (0)
5797 <bf>type <filearea>/<name></bf> Look at the contents of a file in one of the fileareas
5801 Type out the contents of a file in a filearea. So, for example, in
5802 filearea 'bulletins' you want to look at file 'arld051' you would
5805 TYPE bulletins/arld051
5808 See also SHOW/FILES to see what fileareas are available and a
5810 <sect1>uncatchup <node call> all|[msgno> ...] (5)
5814 <bf>uncatchup <node call> all|[msgno> ...]</bf> Unmark a message as sent
5818 When you send messages the fact that you have forwarded it to another node
5819 is remembered so that it isn't sent again. When you have a new partner
5820 node and you add their callsign to your /spider/msg/forward.pl file, all
5821 outstanding non-private messages will be forwarded to them. This may well
5822 be ALL the non-private messages. You can prevent this by using these
5827 catchup GB7DJK 300 301 302 303 500-510
5830 and to undo what you have just done:-
5833 uncatchup GB7DJK all
5834 uncatchup GB7DJK 300 301 302 303 500-510
5837 which will arrange for them to be forward candidates again.
5839 Order is not important.
5840 <sect1>unset/announce (0)
5844 <bf>unset/announce</bf> Stop announce messages coming out on your terminal
5848 <sect1>unset/anntalk (0)
5852 <bf>unset/anntalk</bf> Stop talk like announce messages on your terminal
5856 The announce system on legacy cluster nodes is used as a talk
5857 substitute because the network is so poorly connected. If you:
5863 you will suppress several of these announces, you may miss the odd
5864 useful one as well, but you would probably miss them anyway in the
5865 welter of useless ones.
5871 allows you to see them again. This is the default.
5872 <sect1>unset/baddx <call>.. (8)
5876 <bf>unset/baddx <call>..</bf> Propagate a dx spot with this callsign again
5880 Setting a word as 'baddx' will prevent spots with that word in the
5881 'spotted' field (as in: DX 14001.1 FR0G)of a DX spot from going any
5882 further. They will not be displayed and they will not be sent onto
5885 The word must be written in full, no wild cards are allowed eg:-
5888 set/baddx FORSALE VIDEO FR0G
5891 To allow a word again, use the following command ...
5897 <sect1>unset/badnode <call>.. (8)
5901 <bf>unset/badnode <call>..</bf> Allow spots from this node again
5905 Setting a callsign as a 'badnode' will prevent spots from that node
5906 going any further. They will not be displayed and they will not be
5907 sent onto other nodes.
5909 The call must be a full eg:-
5915 will stop anything from K1TTT. If you want SSIDs as well then you must
5916 enter them specifically.
5922 will allow spots from him again.
5924 Use with extreme care. This command may well be superceeded by FILTERing.
5925 <sect1>unset/badspotter <call>.. (8)
5929 <bf>unset/badspotter <call>..</bf> Allow spots from this callsign again
5933 Setting a callsign as a 'badspotter' will prevent spots from this callsign
5934 going any further. They will not be displayed and they will not be
5935 sent onto other nodes.
5937 The call must be written in full, no wild cards are allowed eg:-
5940 set/badspotter VE2STN
5943 will stop anything from VE2STN. This command will automatically
5944 stop spots from this user, regardless of whether or which SSID
5945 he uses. DO NOT USE SSIDs in the callsign, just use the callsign
5949 unset/badspotter VE2STN
5952 will allow spots from him again.
5954 Use with extreme care. This command may well be superceded by FILTERing.
5955 <sect1>unset/badword <word>.. (8)
5959 <bf>unset/badword <word>..</bf> Propagate things with this word again
5963 Setting a word as a 'badword' will prevent things like spots,
5964 announces or talks with this word in the the text part from going any
5965 further. They will not be displayed and they will not be sent onto
5968 The word must be written in full, no wild cards are allowed eg:-
5971 set/badword annihilate annihilated annihilation
5974 will stop anything with these words in the text.
5977 unset/badword annihilated
5980 will allow text with this word again.
5981 <sect1>unset/beep (0)
5985 <bf>unset/beep</bf> Stop beeps for DX and other messages on your terminal
5989 <sect1>unset/debug <name> (9)
5993 <bf>unset/debug <name></bf> Remove a debug level from the debug set
5997 You can choose to log several different levels. The levels are
6007 You can show what levels you are logging with SHOW/DEBUG
6012 <bf>unset/dx</bf> Stop DX messages coming out on your terminal
6016 <sect1>unset/dxcq (0)
6020 <bf>unset/dxcq</bf> Stop CQ Zones on the end of DX announcements
6024 Display both the Spotter's and the Spotted's CQ Zone on the end
6025 of a DX announcement (there is just enough room). Some user programs
6026 cannot cope with this. The Spotter's CQ is on the RHS of the
6027 time, the Spotted's CQ is on the LHS.
6029 Conflicts with: SET/DXGRID, SET/DXITU, SHOW/USSTATE
6031 Do a STAT/USER to see which flags you have set if you are confused.
6032 <sect1>unset/dxgrid (0)
6036 <bf>unset/dxgrid</bf> Stop QRA Grid Squares on the end of DX announcements
6040 A standard feature which is enabled in version 1.43 and above is
6041 that if the spotter's grid square is known it is output on the end
6042 of a DX announcement (there is just enough room). Some user programs
6043 cannot cope with this. You can use this command to reset (or set)
6046 Conflicts with: SET/DXCQ, SET/DXITU
6048 Do a STAT/USER to see which flags you have set if you are confused.
6049 <sect1>unset/dxitu (0)
6053 <bf>unset/dxitu</bf> Stop ITU Zones on the end of DX announcements
6057 Display both the Spotter's and the Spotted's ITU Zone on the end
6058 of a DX announcement (there is just enough room). Some user programs
6059 cannot cope with this. The Spotter's ITU is on the RHS of the
6060 time, the Spotted's ITU is on the LHS.
6062 Conflicts with: SET/DXGRID, SET/DXCQ, SHOW/USSTATE
6064 Do a STAT/USER to see which flags you have set if you are confused.
6065 <sect1>unset/echo (0)
6069 <bf>unset/echo</bf> Stop the cluster echoing your input
6073 If you are connected via a telnet session, different implimentations
6074 of telnet handle echo differently depending on whether you are
6075 connected via port 23 or some other port. You can use this command
6076 to change the setting appropriately.
6078 The setting is stored in your user profile.
6080 YOU DO NOT NEED TO USE THIS COMMAND IF YOU ARE CONNECTED VIA AX25.
6081 <sect1>unset/email (0)
6085 <bf>unset/email</bf> Stop personal msgs being forwarded by email
6089 If any personal messages come in for your callsign then you can use
6090 these commands to control whether they are forwarded onto your email
6091 address. To enable the forwarding do something like:-
6094 SET/EMAIL mike.tubby@somewhere.com
6097 You can have more than one email address (each one separated by a space).
6098 Emails are forwarded to all the email addresses you specify.
6100 You can disable forwarding by:-
6106 <sect1>unset/here (0)
6110 <bf>unset/here</bf> Tell the system you are absent from your terminal
6114 <sect1>unset/hops <call> ann|spots|route|wwv|wcy (8)
6118 <bf>unset/hops <call> ann|spots|route|wwv|wcy</bf> Unset hop count
6122 Set the hop count for a particular type of broadcast for a node.
6124 This command allows you to set up special hop counts for a node
6125 for currently: announce, spots, wwv and wcy broadcasts.
6129 set/hops gb7djk ann 10
6130 set/hops gb7mbc spots 20
6133 Set SHOW/HOPS for information on what is already set. This command
6134 creates a filter and works in conjunction with the filter system.
6136 You can unset the hops with command UNSET/HOPS. For example:-
6139 unset/hops gb7djk ann
6140 unset/hops gb7mbc spots
6143 <sect1>unset/isolate (9)
6147 <bf>unset/isolate</bf> Stop Isolation of a node from the rest of the network
6151 Remove isolation from a node - SET/ISOLATE
6152 <sect1>unset/lockout <call> (9)
6156 <bf>unset/lockout <call></bf> Allow a callsign to connect to the cluster
6160 <sect1>unset/logininfo (0)
6164 <bf>unset/logininfo</bf> Inform when a station logs out locally
6168 <sect1>unset/password <call> ... (9)
6172 <bf>unset/password <call> ...</bf> Delete (remove) a user's password
6176 This command allows the sysop to completely delete and remove a
6177 password for a user.
6178 <sect1>unset/privilege (0)
6182 <bf>unset/privilege</bf> Remove any privilege for this session
6186 You can use this command to 'protect' this session from unauthorised
6187 use. If you want to get your normal privilege back you will need to
6188 either logout and login again (if you are on a console) or use the
6190 <sect1>unset/prompt (0)
6194 <bf>unset/prompt</bf> Set your prompt back to default
6198 This command will set your user prompt to exactly the string that you
6199 say. The point of this command to enable a user to interface to programs
6200 that are looking for a specific prompt (or else you just want a different
6207 UNSET/PROMPT will undo the SET/PROMPT command and set you prompt back to
6209 <sect1>unset/register <call> ... (9)
6213 <bf>unset/register <call> ...</bf> Mark a user as not registered
6217 Registration is a concept that you can switch on by executing the
6220 set/var $main::regreq = 1
6223 command (usually in your startup file)
6225 If a user is NOT registered then, firstly, instead of the normal
6226 motd file (/spider/data/motd) being sent to the user at startup, the
6227 user is sent the motd_nor file instead. Secondly, the non registered
6228 user only has READ-ONLY access to the node. The non-registered user
6229 cannot use DX, ANN etc.
6231 The only exception to this is that a non-registered user can TALK or
6232 SEND messages to the sysop.
6234 <sect1>unset/talk (0)
6238 <bf>unset/talk</bf> Stop TALK messages coming out on your terminal
6242 <sect1>unset/usstate (0)
6246 <bf>unset/usstate</bf> Stop US State info on the end of DX announcements
6250 If the spotter's or spotted's US State is known it is output on the
6251 end of a DX announcement (there is just enough room).
6253 A spotter's state will appear on the RHS of the time (like
6254 SET/DXGRID) and the spotted's State will appear on the LHS of the
6255 time field. Any information found will override any locator
6256 information from SET/DXGRID.
6258 Some user programs cannot cope with this. You can use this command
6259 to reset (or set) this feature.
6261 Conflicts with: SET/DXCQ, SET/DXITU
6263 Do a STAT/USER to see which flags you have set if you are confused.
6264 <sect1>unset/wcy (0)
6268 <bf>unset/wcy</bf> Stop WCY messages coming out on your terminal
6272 <sect1>unset/wwv (0)
6276 <bf>unset/wwv</bf> Stop WWV messages coming out on your terminal
6284 <bf>unset/wx</bf> Stop WX messages coming out on your terminal
6292 <bf>who</bf> Show who is physically connected
6296 This is a quick listing that shows which callsigns are connected and
6297 what sort of connection they have
6298 <sect1>wx <text> (0)
6302 <bf>wx <text></bf> Send a weather message to local users
6306 <sect1>wx full <text> (0)
6310 <bf>wx full <text></bf> Send a weather message to all cluster users
6314 <sect1>wx sysop <text> (5)
6318 <bf>wx sysop <text></bf> Send a weather message to other clusters only
6322 Weather messages can sometimes be useful if you are experiencing an extreme
6323 that may indicate enhanced conditions